HID Fargo DTC1000Me User Manual Download

Page: 77 / 84

Chapter

December 2016

Page 6-1

Firmware Upgrades

6.1

Upgrade Information

To upgrade the printer’s firmware, perform the following steps:

1. Run the

FARGO Workbench Printer Utility

2. If running FARGO Workbench Version 3 or greater:

a. Select the

Update Manager Workbench Utility

b. Select the printer(s) to update.

c. Click

Select Firmware file…

option to locate or enter this latest firmware file

(FRW-00373_DTC100_v2.3.3.20.frm).

d. Browse for the firmware file or enter the firmware file name and click

Open

e. Click

Begin Updating Firmware

to send the file to the printer(s).

3. If running a FARGO Workbench release prior to Version 3:

a. Select the

Application Menu

at the upper left, and select

Upgrade Firmware

b. Enter the firmware file name or click

Browse

to find and select this latest firmware file

(FRW-00373_DTC100_v2.3.3.20.frm).

c. Click

to send the file to the printer(s).

4. Restart the printer if it does not restart automatically.

Summary of Contents for Fargo DTC1000Me





















































































Search results

Summary of Contents for Fargo DTC1000Me

Reviews:

Related manuals for Fargo DTC1000Me

Brands by name

Popular brands

HID Fargo DTC1000Me, User Manual

Search results

Summary of Contents for Fargo DTC1000Me

Reviews:

Related manuals for Fargo DTC1000Me

Brands by name

Popular brands