HID Fargo DTC1000Me Page 39 User Manual Download

Page: 39 / 84

December 2016

Page 4-13

PLT-01668, Version: 1.2

Printer Preferences

4.1.1.5 Advanced Settings Tab

Use the Toolbox

Advanced Settings

tab for adjusting the internal printer settings, which are

customized for every printer at the factory and saved directly within the printer's memory.

Note:

Select

Restore Defaults

to restore the internal default settings.

Settings enable users to change the values for firmware settings by clicking on the Current column.

Field

Description

Setting Column

Displays label for setting. See the Setting Column Fields table below.

Default Column

Displays default value for setting

Current Column

Displays current value for setting

Apply Button

Applies changed values.

Restore Defaults Button

Restores the default values.

Enable Mag Verify

Check this box to verify that the data is written to the tracks correctly.

Summary of Contents for Fargo DTC1000Me





















































































Search results

Summary of Contents for Fargo DTC1000Me

Reviews:

Related manuals for Fargo DTC1000Me

Brands by name

Popular brands

HID Fargo DTC1000Me, User Manual

Search results

Summary of Contents for Fargo DTC1000Me

Reviews:

Related manuals for Fargo DTC1000Me

Brands by name

Popular brands