HID Fargo DTC1000Me Page 67 User Manual Download

Page: 67 / 84

December 2016

Page 5-3

PLT-01668, Version: 1.2

System Overview - Troubleshooting

6. When downloading an upgrade file, both buttons are blue and blink. If the unit is a DTC1250E,

you are notified that the upgrade is in process.

7. If a language (other than English) is currently selected, you can press and hold the

Pause

button during the power-up sequence to change the language back to English.

8. When no printer display is available, press or hold the buttons to access some internal tests.



To print a card with the Printer Settings, press the

Pause

button and hold for 4+ seconds

when the printer is ready and idle.



To print the Alignment or the Self Test, press and hold the

Pause

button during the power-

up sequence.

Summary of Contents for Fargo DTC1000Me





















































































Search results

Summary of Contents for Fargo DTC1000Me

Reviews:

Related manuals for Fargo DTC1000Me

Brands by name

Popular brands

HID Fargo DTC1000Me, User Manual

Search results

Summary of Contents for Fargo DTC1000Me

Reviews:

Related manuals for Fargo DTC1000Me

Brands by name

Popular brands