HID Fargo DTC1000Me User Manual Download | Manualshive

Page: 70 / 84

background image

Page 5-6

December 2016

System Overview - Troubleshooting

PLT-01668, Version: 1.2

# 44
Flipper Jam/
Home Error

A card has
become
jammed in the
printer’s
flipper table.
The flipper
failed to
position
properly while
aligning a card
or flipping a
card.

Clear any cards in the flipper table using the buttons to move the card
out. Resume printing.
The flipper table should be level when the printer is powered up. If the
flipper Table is at an angle, open the card output door and manually
level it. Then cycle the printer power to reset.
Reset the printer and retry. If problem persists call for technical
assistance.

# 45
No Flip Module
installed

Request to
print on 2

nd

side of card,
but no flipper
is installed.

If a Flipper Module is present, ensure that the

Print Both Sides

option

in the printer driver is set correctly.
Install a flipper module.

# 64
# 65
# 66
Reboot Required

Unspecified
system error
detected by
the printer
firmware.

Reset the printer and try again.
If this problem persists, call for technical assistance.

# 68
Card in Printer

A card is
jammed in the
print station or
card flipping
area of the
Printer.

Clear the jam and press the

Pause

button.

# 70
Multiple Feed

Multiple cards
were fed into
the printer.

Verify the card thickness is set to the thickness of your cards, then
press the

Pause

button.

Check for card slippage. If necessary, run the printer cleaning routine.
Verify the cleaning roller is properly installed on the ribbon cartridge.
Verify the cards are not sticking together.

# 81
Unable to Feed

The printer is
unable to feed
a card from
the input card
hopper.

Check the following, then press the

Pause

button to continue.

Verify the card thickness setting is set to the thickness of your cards.
Verify the Cleaning roller is properly installed on the Ribbon Cartridge.
Check for card slippage. If necessary, run the Printer cleaning routine.
Verify that your cards are within the perimeters accepted card size
range.
Verify the cards are not sticking together.

# 82 Mag Jam

A card is
jammed
magnetic
station

Clear any cards in the magnetic station using the buttons to move the
card out.
Press the Pause button to continue.

# 91
Ribbon Out

The print
ribbon has run
out.

Install a new ribbon.
Press the

Pause

button to continue or the

ON/OFF

button to cancel.

Error Message

Cause

Solution

«
...
68
69
70
71
72
...
»

Summary of Contents for Fargo DTC1000Me





















































































Reviews:

No comments

Related manuals for Fargo DTC1000Me

IMAGERUNNER ADVANCE C5051

Brand: Canon Pages: 72

iPF710 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 92

iPF8000S - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 8

imageRUNNER ADVANCE C9075S PRO

Brand: Canon Pages: 48

Two-Knife Booklet Trimmer-A1

Brand: Canon Pages: 32

Perfect Binder-C1

Brand: Oce Pages: 82

IMAGERUNNER 7095 PRINTER

Brand: Canon Pages: 615

imageRUNNER C3125i

Brand: Canon Pages: 816

Brand: oliser Pages: 6

WORKCENTRE 5735

Brand: Xerox Pages: 50

Brand: Lanier Pages: 6

Brand: Colorjet Pages: 52

AficioSP C410DN

Brand: Ricoh Pages: 204

Intelliprint cL160

Brand: Genicom Pages: 216

ECOSYS P6230cdn

Brand: Kyocera Pages: 258

Brand: Hitt Marking Devices Pages: 27

Accel-a-Writer 8200

Brand: Xante Pages: 12

Brand: Star Micronics Pages: 130

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands