Herutu SD-4 Operation Manual Download Page 13 | Manualshive

Page: 13 / 48

background image

8

1-8 Installation

1-8-1 Installation procedure

(1) Mount the mounting stay to the installation area with wood screws or small screws.

Mount the main body onto the mounting stay with ornamental screws loosely tightened.

* In the case the mounting stay is attached to the main body, remove the two ornamental

screws from both sides and detach the mounting fittings.

(2) To the Actual count (UP terminal) on the input terminal block, connect the non-voltage

contact for counting up the input signals from relays, micro switches, limit switches, etc.

Also, establish a connection to each of the other input terminals as needed.

(3) Determine the angle at which the display panel (data display and LED

’s) is easy to see

and operate, and then fix the main body by fully tightening the ornamental screws on

both sides.

(4) Insert an applicable plug firmly into the DC jack and supply the power of DC12V/0.8A or

more.

(Applicable plug: φ2.1(I.D.) x φ5.5(O.D.) mm with center negative)

The main body has a build-in microprocessor, which means there is a possibility that the data
may collapse due to power fluctuation or flicker. Take power supply from a location free from
power fluctuation or flicker.

For the non-voltage contacts to be connected to the input terminal block, use the ones with less
chattering that can steadily turn on/off the voltage/current of 12V/10mA.

1-8-2 Input terminal block

For the input signals to be connected to the terminal block, use the ones with less chattering

that can steadily turn on/off the voltage/current of 12V/10mA. Keep a time interval of at

least 50msec between input signals. Also, keep 50msec or more from when one input

signal is turned off till another input signal is turned on.

<Input circuit>

Non-voltage contact input circuit (rating: DC12V/10mA)

R

フォトカプラ

COM

INPUT

+12V

Photocoupler

«
...
11
12
13
14
15
...
»

Summary of Contents for SD-4

















































Reviews:

No comments

Related manuals for SD-4

Brand: Kamstrup Pages: 100

Brand: Kamstrup Pages: 16

Brand: Kamstrup Pages: 12

Brand: Kamstrup Pages: 60

Brand: Kamstrup Pages: 136

Brand: Kamstrup Pages: 16

Brand: Kamstrup Pages: 155

Brand: Kathrein Pages: 10

Brand: Sensia Pages: 16

Brand: ColorLite Pages: 68

Brand: Gearx Pages: 19

Brand: LaserLiner Pages: 52

Brand: Veris Pages: 8

Brand: Olimpus Pages: 12

Brand: Polimaster Pages: 6

Brand: STONEX Pages: 99

Brand: Caen Pages: 63

Brand: Caen Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands