Henny Penny Evolution Elite EEE-153 Operator'S Manual Download Page 76

Page: 76 / 80

Problem

Cause

Correction

Oil foaming or boiling over

top of vat

• Water in oil

• Improper or bad oil

•

Improper filtering

• Improper rinsing after

cleaning the vat

• Drain and clean oil

• Use recommended oil

•

Refer to filtering procedures

• Clean and rinse vat and then dry thoroughly

Oil will not drain from vat

• Drain valve clogged

with crumbs

• Drain trough clogged

• Open valve, force cleaning brush through

drain

• Remove right side panel and remove plug

from end of trough and clean trough

Filter motor runs but pumps

oil slowly

• Filter line connections

loose

• Filter paper or pad

clogged

•

Tighten all filter line connections

•

Change filter paper or pad

Bubbles in oil during entire

filtering process

• Filter pan not

completely engaged

• Filter pan clogged

• Damaged O-ring on

filter line receiver on

fryer

•

Make sure filter pan return line is pushed

completely into the receiver on the fryer

• Clean pan and change paper or pad

• Change O-ring

Control error code “E-31”

• Elements are up

• Lower elements back into vat

Filter motor will not run

• Power cord for vat #1

is not plugged-in

• Open circuit

• The thermal reset

button on the rear of

the pump motor is

tripped

• Plug power cord into receptacle

• Breakers in fryer tripped; open left door and

reset breaker on fryer

• Allow time for the motor to cool and then,

using a screwdriver, press hard against the

button until it clicks

7-1. TROUBLE SHOOTING GUIDE

(Continued)

Aug. 2011

Summary of Contents for Evolution Elite EEE-153

















































































Search results

Summary of Contents for Evolution Elite EEE-153

Reviews:

Related manuals for Evolution Elite EEE-153

Brands by name

Popular brands

Henny Penny Evolution Elite EEE-153, Operator'S Manual

Search results

Summary of Contents for Evolution Elite EEE-153

Reviews:

Related manuals for Evolution Elite EEE-153

Brands by name

Popular brands