Henny Penny Evolution Elite EEE-153 Operator'S Manual Download Page 36

Page: 36 / 80

3-13. DISCARDING OIL USING

OPTIONAL OIL DISCARD

SHUTTLE-ODS-450

(Continued)

6. Press

button and “IS DISPOSAL UNIT IN PLACE?

“YES NO”shows in display.

7. With discard shuttle rolled into place (Figure 3), press

button

and display shows “OPEN DRAIN”. Pull-out on drain knob

to open drain and display shows “DRAINING”. Oil now

drains from the vat into the shuttle.

8. Display shows “VAT EMTY “YES NO”. Verify that vat is

empty, and press

button.

9. Display shows “CLEAR OLD OIL FROM OIL LINES”

“

=PUMP” “X= DONE”. Press and hold

button for a

few seconds to clear old oil from lines. Once cleared, press

button.

10. Display shows “CLN VAT COMPLETE” “YES NO”. Once

vat is clean, press

button and display shows “CLOSE

DRAIN”. Push-in on the drain knob.

11. Display shows “MANUAL FILL POT”, followed by “IS POT

FILLED?”, along with “YES NO”. Fill the vat to the lower

indicator line on the rear of the vat and then press

button.

12. Remove the oil disposal shuttle from under fryer and replace

with the filter pan assembly.

13. Close and latch the cover and roll oil disposal shuttle to disposal

container.

14. Press down on top of brake to secure unit in place. Figure 5.

15. Disconnect fitting from top of ODS and connect to disposal

container. Figure 6.

16. Using the power cord on the back of the shuttle handle, plug it

into the short cord from the junction box. Figures 7 & 8.

17. Turn power switch to the ON position. Figure 8.

Figure 5

Figure 6

Figure 7

Press down to lock

Press to release

Figure 8

Aug. 2011

Summary of Contents for Evolution Elite EEE-153

















































































Search results

Summary of Contents for Evolution Elite EEE-153

Reviews:

Related manuals for Evolution Elite EEE-153

Brands by name

Popular brands

Henny Penny Evolution Elite EEE-153, Operator'S Manual

Search results

Summary of Contents for Evolution Elite EEE-153

Reviews:

Related manuals for Evolution Elite EEE-153

Brands by name

Popular brands