Henny Penny Evolution Elite EEE-153 Operator'S Manual Download Page 27

Page: 27 / 80

After trying to fill the vat 3 times without success, the controls then

shows “CHANGE FILTER PAD?” “YES NO”. If changing the filter

pad at this time, press √

and change filter pad following the proce

dures in the Changing

the Filter Pad or Paper Section. Controls

return to normal operation.

If filter pad is to be changed at a later time, press X button and

“CHANGE FILTER PAD?” reminder shows 15 minutes later.

During the next AIF with a new filter pad, if the vat is not filled after

3 tries, the display shows “FILTER SERVICE REQUIRED-SEE

TROUBLESHOOTING GUIDE”.

10.

If the “Service Required” message appears, then every 15 minutes the

display shows “FILTER PROBLEM FIXED? YES NO”. If the prob-

lem has not been fixed, press X button. Once the problem has been

resolved, press

√

and controls return to normal operation.

To help ensure the vat fills completely, make sure filter pan is cleaned at

least daily, filter pad is changed, make sure JIB is full and that “O” rings

on the filter pan are in good condition.

3-10.

B FILTER - SMART TOUCH

(continued)

March 2015

Summary of Contents for Evolution Elite EEE-153

















































































Search results

Summary of Contents for Evolution Elite EEE-153

Reviews:

Brands by name

Popular brands

Henny Penny Evolution Elite EEE-153, Operator'S Manual

Search results

Summary of Contents for Evolution Elite EEE-153

Reviews:

Brands by name

Popular brands