Henny Penny Evolution Elite EEE-153 Operator'S Manual Download Page 25

Page: 25 / 80

6. If

the oil has not pumped back to the proper level in the vat

during the SmartFilter Express™ process, press

button

for NO and pump runs for another 30 seconds.

7. Display shows “IS POT FILLED?” “YES NO”. Make

sure vat is full and then press

button and display shows

and the control returns to normal operation. Press

button

and pump runs for another 30 seconds. You can try to fill

the vat 3 times.

Filter Error

8. After trying to fill the vat 3 times without success, the

controls then shows “CHANGE FILTER PAD?” “YES

NO”. If changing the filter pad at this time, press

and

change filter pad following the procedures in the Changing

the Filter Pad Section. Controls return to normal operation.

If filter pad is to be changed at a later time, press

button

and “CHANGE FILTER PAD?” reminder shows 15

minutes later.

9. During the next SmartFilter Express™ with a new

filter pad, if the vat is not filled after 3 tries, the display

shows “FILTER SERVICE REQUIRED-SEE

TROUBLESHOOTING GUIDE”.

If the “Service Required” message appears, then every

15 minutes the display shows “FILTER PROBLEM

FIXED? YES NO”. If the problem has not been fixed, press

button. Once the problem has been resolved, press

and controls return to normal operation.

To help ensure the vat fills completely, make sure filter pan

is cleaned at least daily, filter pad is changed, make sure

BIB is full and that “O” rings on the filter pan are in good

condition.

3-10. A FILTER - MANUAL

(Continued)

April 2015

Summary of Contents for Evolution Elite EEE-153

















































































Search results

Summary of Contents for Evolution Elite EEE-153

Reviews:

Related manuals for Evolution Elite EEE-153

Brands by name

Popular brands

Henny Penny Evolution Elite EEE-153, Operator'S Manual

Search results

Summary of Contents for Evolution Elite EEE-153

Reviews:

Related manuals for Evolution Elite EEE-153

Brands by name

Popular brands