manualshive.com logo in svg

Henny Penny Evolution Elite EEE-153, Operator'S Manual

Share
Download
Henny Penny Evolution Elite EEE-153 Operator'S Manual Download Page 60

56

To Change Times and Temperatures

7.  Press          button  until “COOK TIME” shows in the 

display, and then use the product buttons, or the             

and        buttons, to change the time in minutes and 

seconds, to a maximum of 59:59.

8. Press        button  and “TEMP” shows in the display, along

with the preset temperature on the right side of the display.

Press the product buttons, or the         and        buttons, to

change the temperature.  The temperature range is 190°F

(88°C) to 375°F (191°C).

Cook ID Change

9.  Press          button  until “COOK ID” shows in the display 

along with the product ID.  For example, NUG would 

be the ID for nuggets.  Use the product buttons, or the         

and         buttons, to change the ID.

Alarms (1 & 2)

11. Press           button until “ALRM 1” shows in the left 

display, and an alarm time in the right display. Press the 

product buttons, or the         and           buttons, to set an 

 alarm. 

Ex., If a Cook Cycle was set at 3 minutes, and an alarm  

was to go off after 30 seconds into the Cook Cycle, “2:30” 

would be set in the display at this time. When the timer  

counts down to 2:30 the alarm sounds.

After alarm time is set, press        button  and “ALRM 2”  

shows in display, and a second alarm can be programmed.

Quality Timer (hold time)

12. Press          button until “QUAL TMR” shows in the display 

along with the preset holding time.  Press the product 

buttons, or the         and           buttons,to adjust holding 

time, up to 59:59.

Global Filter Tracking

Include in Filter Count 

13a.  Press          button  until “INCL IN FLTR CNT” flashes in 

display along with “YES” or “NO”. Using          and  

buttons, change the display to “YES” if that product’s Cook 

Cycles are to be counted as part of the recommended filter 

process.  Set to “NO” if it is not to be included. 

5-1.   MODIFYING PRODUCT

SETTINGS (Continued)

Aug. 2011

Summary of Contents for Evolution Elite EEE-153

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands