Henny Penny Evolution Elite EEE-153 Operator'S Manual Download

Page: 48 / 80

3-17.

C COLD SOAK

PROCEDURE

Dispose of the oil in the fryer.

Fill the fryer with cleaning soution and let it sit overnight.

Use the long-handled fryer brush or a blue scouring pad in an up

and down motion (scour the sides of the kettle and the heating

coils).

Use the L-shaped brush to scrub between the heating coils and

the sides of the fryer kettle.

Place a three-gallon clear plastic bucket or a full sized meat pan

under the drain valve.

Use step 4 in the filter menu to drain the cold soak cleaning solu

tion into the bucket or pan.

Use the salad cart to transport the bucket or pan if necessary.

Discard the cold soak cleaning solution in the mop sink.

Call out “hot water” when carrying hot water to the fryers.

Failure to do so may result in minor burns.

Fill the double boiler bottom half full with hot tap water.

Carefully pour the water into the fryer.

Use the salad cart for multiple trips with hot water.

10.

Repeat this procedure two or more times for the rinse water to

reach the fryer’s fill line.

11.

Place a three-gallon clear plastic bucket or a full sized meat pan

under the drain valve.

12.

Use step 4 in the filter menu to drain the hot water into the

bucket or pan.

FIRE RISK

Do not exert pressure on the heating elements or fire may

occur, resulting in personal injury and/or property damage.

Oct

. 201

Summary of Contents for Evolution Elite EEE-153

















































































Search results

Summary of Contents for Evolution Elite EEE-153

Reviews:

Related manuals for Evolution Elite EEE-153

Brands by name

Popular brands

Henny Penny Evolution Elite EEE-153, Operator'S Manual

Search results

Summary of Contents for Evolution Elite EEE-153

Reviews:

Related manuals for Evolution Elite EEE-153

Brands by name

Popular brands