Henny Penny Evolution Elite EEE-153 Operator'S Manual Download Page 65

Page: 65 / 80

Audio Tone (SP-5)

Press

button and “SP-5” and “TONE” flash in the

left display. Press the or , or use product buttons,

to adjust the tone of the speaker, 2000 being the maximum

value and 50 the minimum.

Liquid or Solid Cooking Oil Used (SP-6)

Press

button until “SP-6 MELT CYCLE SELECT”

scrolls in the left display. Unless solid oil is being used in

the vats the right display should show “1.LIQUID”.

If solid oil is used, the unit MUST BE equipped to handle

solid oil. Use the and buttons to change the right

display to “2.SOLID”

Idle Mode Enabled (SP-7)

An Idle Mode allows the oil temperature to drop to a lower

temperature when not in use. This savies on oil and utilities.

Press

button and “SP-7” and “IDLE MODE

ENABLED?” flash in the left display. Press the or

buttons to choose YES” or “NO”.

With “YES” in the display, press button and “SP-7A”

and “USE ‘0’ FOR IDLE” flash on the left display. Press

the or buttons to select “YES” or “NO”. If “YES”

is selected, an Idle Mode can be programmed in product

button

Press button and “SP-7B” and “AUTOIDLE

MINUTES” flash in the left display. Press the or

, or use product buttons, to set the time (0 to 60 minutes)

fryer stays idle before the auto-idle is enabled.

Ex.,“30” means, if product is not cooked in that vat for 30

minutes, the control automatically cools the oil down to the

idle setpoint temperature

Press

button and “SP-7C” and “IDLE SETPT” flash in

the left display. Press the or

, or use product

buttons, to set the idle temperature 200

to 375

F (93 to

191

C) .

6-1. SPECIAL PROGRAM

MODE (Continued)

Aug. 2011

Summary of Contents for Evolution Elite EEE-153

















































































Search results

Summary of Contents for Evolution Elite EEE-153

Reviews:

Related manuals for Evolution Elite EEE-153

Brands by name

Popular brands

Henny Penny Evolution Elite EEE-153, Operator'S Manual

Search results

Summary of Contents for Evolution Elite EEE-153

Reviews:

Related manuals for Evolution Elite EEE-153

Brands by name

Popular brands