Installation Instructions and Instructions for Use
Subject to technical modifications. – Date of Issue
September/2020
11
Servicing, maintenance and repair
Maintenance
Maintenance
All inspection and maintenance works must be carried out by a
specialised company from HELLA or a HELLA partner. Regularly check
the electrical wires of motor driven units for damage. Check the
mechanical parts of your unit for visible damage. After exceptional
events such as storm, hail, sleet, maloperation or the like, the unit must
be checked for noticeable damage prior to operating it. If the unit is
damaged, it must not be used; consult authorized specialist staff
immediately. It is recommended to have the unit maintained by
specialist staff on an annual basis. This way wear is detected at an
early stage and damage to the unit is prevented.
To perform the above mentioned inspection of all mechanical parts, the
inspection cover must be removed by loosening the fixing screws on the
end caps (see Chapter “Awning Installation” in reverse order).
- Inspection of all screw fixing connections for correct fit (Coupling and
fixing screws - clamping element)
- Inspection of the position of the arm bearing and/or the clamping
element on the bracket
- Inspection of the bracket fixing for a correct fit (the bracket has to
adhere to the mounting base without a gap)!
Repair works
Repair works
Improper repair works may cause both risk of injury to persons or
damage to the units. All repair works must be carried out by a
specialised company from HELLA or a HELLA partner. Use original
HELLA spare parts only.
Installation Instructions and Instructions for Use
12
Subject to technical modifications. – Date of Issue
September/2020
Operating guidelines
Motor drive
The awning can be extended
or retracted by activating a
switch, a hand-held radio
transmitter or an automatic
device.
The end points of the drive
are adjusted ex works.
Please observe the enclosed
instructions of the
manufacturer of the drive, if
any modification is required.
Lighting
By activating a radio transmitter or an automatic device the lighting is
switched on or off or dimmed. You will find detailed information in the
enclosed instructions of the manufacturer.
Hand-held radio transmitter with scroll wheel
Setting the scroll wheel function with hand-held radio transmitter “Somfy
Situo 5 Variation A/M io”:
- Open the rear housing cover
- Set the selector switch for the operating mode “E” to position 2
In this way the scroll wheel reacts to the LED lighting and heating. You will
find detailed information in the enclosed instructions of the manufacturer.
2
E
Installation Instructions and Instructions for Use
Subject to technical modifications. – Date of Issue
September/2020
13
Before installation
Check the product immediately for possible shipping damage and for
compliance with the delivery receipt.
If parts are missing or damaged, please consult your supplier immediately.
Check the mounting base and ensure that the mounting material to be
used complies with the given conditions to guarantee proper installation. In
case of doubt, please seek advice from a specialist enterprise for fixing
techniques.
The packaging cardboard box should not be exposed to humidity. To
protect it from rain during transport, it should be covered by a foil.
Carry larger units by two persons. Transport and store the units carefully
to prevent injury of persons and damage to the product.
Remove the packaging material carefully. When using a knife, be careful
not to damage the packaging content and to avoid cuts!
Dispose of the packaging material via recycling.
Caution!
A wrong installation can endanger the user seriously. Please strictly
observe the installation instructions. Close off the place of installation.
When working at higher heights, there is risk of falling. Suitable ascent
supports, scaffoldings and fall protection devices are to be used. Please
make sure that the ascent supports stand solidly and provide a firm grip.
Installation Instructions and Instructions for Use
14
Subject to technical modifications. – Date of Issue
September/2020
Overview Cassette awning PAN 7040
Legend
End cap
Front rail
Folding arm
Bracket
Tilting arm bearing
Cassette profile
Entry assistance (as required)
The LED control unit (according to the design)
is stowed in the profiled pipe 35x35 mm (between wall and cassette profile)
1
2
3
4
6
8
7
5
