Hella PAN 7040 Installation Instructions Manual Download Page 21

Installation Instructions and Instructions for Use 

 

 

 

 

 

 

 

HELLA Interior Venetian 
Blinds 

regulate the lighting in a room 
very comfortably, immediately 
gracing it with much more 
atmosphere. 

HELLA Insect screens 

and you decide who is allowed 
to come in and who isn't. 

HELLA Pleated Blind 

folds up very compactly and 
protects very well against the 
sun and nosey glances where 
only little space is available. 

 

 

 

HELLA Outdoor Blinds 

serve for the light regulation, 
as view protection, anti-glare 
blind and heat protection. 

HELLA Front-mounted 
Roller Shutter 

for more safety and protection 
against rain, wind, heat, the 
cold, noise, incident light and 
nosey glances, also available 
for subsequent installation. 

HELLA Facade Awning 

with toggle catch mechanism 
for a lovely facade design with 
perfect heat and glare 
protection. 

  

 
 

For questions, wishes and ideas: 

HELLA In43/(0)4846/6555-0

 

 

HELLA Sonnen- und Wetterschutztechnik GmbH

 

A-9913 Abfaltersbach, No. 125 

Phone: +43/(0)4846/6555-0 

Fax: +43/(0)4846/6555-134 

e-mail: [email protected] 

Internet: http://www.hella.info 

 

  

Summary of Contents for PAN 7040






















Reviews: