Haulotte Group xlb-4725a, Operator'S Maintenance Manual, Page: 65 / 118

HAULOTTE GROUP 4 EQUIPMENT MAINTENANCE
65
TABLE 4-3 ERROR CODE DEFINITIONS
ERROR MESSAGE ERROR DEFINITION TO SIMULATE ERROR TO CLEAR ERROR COMMENTS
128 SHORTED CIRCUIT
FS RET (FWS C24)
Excessive load was
detected when FS Ret
(FWS C24) circuit was
energized Use a piece of wire to
short the FS Ret (FWS
C24) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
129 OPEN CIRCUIT
FS EXT (FWS C25)
A load of less than 70mA
was detected when FS
Ext (FWS C25) circuit
was energized Disconnect a wire from
FS Ext (FWS C25) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
130 SHORTED CIRCUIT
FS RET (FWS C25)
Excessive load was
detected when FS Ext
(FWS C25) circuit was
energized Use a piece of wire to
short the FS Ext (FWS
C25) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
131 OPEN CIRCUIT
DC D FWD (FWS
C26)
A load of less than 70mA
was detected when DC D
Fwd (FWS C26) circuit
was energized Disconnect a wire from
DC D Fwd (FWS C26)
coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
132 SHORTED CIRCUIT
DC D FWD (FWS
C26)
Excessive load was
detected when DC D
Fwd (FWS C26) circuit
was energized Use a piece of wire to
short the DC D Fwd
(FWS C26) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
133 OPEN CIRCUIT
DC D REV (FWS
C27)
A load of less than 70mA
was detected when DC D
Rev (FWS C27) circuit
was energized Disconnect a wire from
DC D Rev (FWS C27)
coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
134 SHORTED CIRCUIT
DC D REV (FWS
C27)
Excessive load was
detected when DC D Rev
(FWS C27) circuit was
energized Use a piece of wire to
short the DC D Rev
(FWS C27) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
135 OPEN CIRCUIT
DC D (FWS C28)
A load of less than 70mA
was detected when DC D
(FWS C28) circuit was
energized Disconnect a wire from
DC D (FWS C28) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
136 SHORTED CIRCUIT
DC D (FWS C28)
Excessive load was
detected when DC D
(FWS C28) circuit was
energized Use a piece of wire to
short the DC D (FWS
C28) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
137 OPEN CIRCUIT
DC D (FWS C29)
A load of less than 70mA
was detected when DC D
(FWS C29) circuit was
energized Disconnect a wire from
DC D (FWS C29) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
138 SHORTED CIRCUIT
DC D (FWS C29)
Excessive load was
detected when DC D
(FWS C29) circuit was
energized Use a piece of wire to
short the DC D (FWS
C29) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
139 OPEN CIRCUIT
DC D (FWS C30)
A load of less than 70mA
was detected when DC D
(FWS C30) circuit was
energized Disconnect a wire from
DC D (FWS C30) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
140 SHORTED CIRCUIT
DC D (FWS C30)
Excessive load was
detected when DC D
(FWS C30) circuit was
energized Use a piece of wire to
short the DC D (FWS
C30) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
141 OPEN CIRCUIT
DC D (FWS C31)
A load of less than 70mA
was detected when DC D
(FWS C31) circuit was
energized Disconnect a wire from
DC D (FWS C31) coil This is a latched error.
Power must be cycled to
clear error Checked only at |
power up
Machines with 4WS
option only
142 SHORTED CIRCUIT
DC D (FWS C31)
Excessive load was
detected when DC D
(FWS C31) circuit was
energized Use a piece of wire to
short the DC D (FWS
C31) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only