Haulotte Group xlb-4725a, Operator'S Maintenance Manual, Page: 57 / 118

HAULOTTE GROUP 4 EQUIPMENT MAINTENANCE
57
ERROR CODE DEFINITIONS – CONTROLS
The
DISPLAY PANEL
located on the ground (lower) control panel, indicates the present operating
status of the aerial work platform. If an error condition is detected, the appropriate error code will be
displayed on this panel.
Refer to Table 4-3 to resolve the error, or contact Haulotte Group Customer Service Department: at
1-800-537-0540 or visit Haulotte Group online at
www.haulotte-usa.com with any additional
questions.
TABLE 4-3 ERROR CODE DEFINITIONS
ERROR MESSAGE ERROR DEFINITION TO SIMULATE ERROR TO CLEAR ERROR COMMENTS
001 MACHINE IS IN
DOWN ONLY MODE
Machine went out of level
with use, moment sense
or load sense circuits
have detected an
overload Level machine, raise
boom and tilt level
sensor This is a self clearing
error. When error
condition is corrected,
error is cleared Error will be displayed
only if boom is raised
002 LOSS OF
PLATFORM
COMMUNICATION
Lower Control has lost
RS485 communication
with Platform Control Open Platform Control
and remove green wire
from J1 This is a latched error.
Power must be cycled to
clear error The Platform Control
"Engine On" LED will also
blink a 2 blink error code.
003 LOSS OF DRIVE
COMMUNICATION
Lower Control has lost
RS485 communication
with Drive Control Open Drive Control and
remove green wire from
J1 This is a latched error.
Power must be cycled to
clear error Machines with Drive
option only. The Drive
Control "Engine On" LED
will also blink a 2 blink
error code.
004 LOSS OF PC
COMMUNICATION
Lower Control has lost
RS232 communication
with PC Connect a PC without
running the configuration
program This is a self clearing
error. When error
condition is corrected,
error is cleared Error message will only
be display if connected to
a PC that is not
communicating.
005 PLATFORM
CONTROL HAS
STUCK KEY
Platform Control has
detected a stuck or
pressed key on power up On Platform Control hold
down a key at power up This is a latched error.
Power must be cycled to
clear error The Platform Control
"Engine On" LED will also
blink a 1 blink error code.
006 DRIVE CONTROL
HAS STUCK KEY
Drive Control has
detected a stuck or
pressed key on power up On Drive Control hold
down a key at power up This is a latched error.
Power must be cycled to
clear error Machines with Drive
option only. The Drive
Control "Engine On" LED
will also blink a 1 blink
error code.
007 DRIVE CONTROL
HAS STUCK
JOYSTICK
Drive Control has
detected a stuck or
pressed joystick on
power up On Drive Control hold
joystick to side at power
up This is a latched error.
Power must be cycled to
clear error Machines with Drive
option only. The Drive
Control "Engine On" LED
will also blink a 3 blink
error code.
008 GROUND
CONTROL HAS
STUCK KEY
Lower Control has
detected a stuck or
pressed key on power up On Lower Control hold
down a key at power up This is a latched error.
Power must be cycled to
clear error The Lower Control
"Power" LED will also
blink a 1 blink error code.
009 BOOM UP
WITHOUT
OUTRIGGERS ON
GROUND
Lower Control has
detected the boom is up
and all four outriggers
are not on the ground Disconnect a wire from
either the boom down or
any outrigger switch and
turn on machine This is a self clearing
error. When error
condition is corrected,
error is cleared
010 LEVEL SENSOR
HAS ERRATIC
OUTPUT
The Lower Control has
detected an erratic
output from the level
sensor Shaking the level sensor
after machine has been
leveled This is a self clearing
error. When error
condition is corrected,
error is cleared This error is suppressed
during extending and
retracting outriggers
011 TRYING TO DRIVE
W/ TRAILER BRAKE
OFF
An attempt was made to
drive machine without
engaging the trailer
brake Trying to drive machine
with trailer brake off This is a self clearing
error. When error
condition is corrected,
error is cleared Machines with Drive and
Set option only
012 ANGLE SENSOR IS
DISCONNECTED
OR BAD
Angle sensor output is
out of range Disconnect Angle Sensor This is a self clearing
error. When error
condition is corrected,
error is cleared Machines with Moment
Sense option only