Haulotte Group 3522A, Operator'S Maintenance Manual

Page: 63 / 142

HAULOTTE GROUP 4 EQUIPMENT MAINTENANCE
63
TABLE 4-3 ERROR CODE DEFINITIONS
ERROR MESSAGE ERROR DEFINITION TO SIMULATE ERROR TO CLEAR ERROR COMMENTS
103 OUTREACH
NEAR MAXIMUM
Boom has exceeded
95% of maximum
outreach Put 500lbs in boom, level
boom and extend until
alarm sounds and error
is displayed This is a self clearing
error. When error
condition is corrected,
error is cleared Machines with Moment
Sense option only
104 OUTREACH
AT MAXIMUM
Boom has reached
maximum outreach
setting Put 500lbs in boom, level
boom and extend until
alarm sounds and error
is displayed This is a self clearing
error. When error
condition is corrected,
error is cleared Machines with Moment
Sense option only
105 OVER MAXIMUM
CYLINDER
PRESSURE
Cylinder pressure has
exceeded maximum
pressure setting Put 500lbs in boom,
lower cylinder pressure
setting using
configuration program
and extend boom until
alarm sounds and error
is displayed This is a latched error.
Power must be cycled to
clear error Machines with Moment
Sense option only
106 OUTREACH
SENSING FAULT
Cylinder safety pressure
switch has detected
maximum pressure
setting Disconnect safety
pressure switch wires This is a latched error.
Power must be cycled to
clear error Machines with Moment
Sense option only
107 ENGINE TEMP
HIGH CHECK
WATER LEVEL
Excessive engine
temperature was
detected Remove wire from
engine temperature
sensor and connect wire
to ground This is a self clearing
error. When error
condition is corrected,
error is cleared Machines with 4WS
option only
108 CHECK
ALTERNATOR
NOT CHARGING
Engine alternator is not
charging Remove P wire from
alternator and connect
wire to ground This is a self clearing
error. When error
condition is corrected,
error is cleared Machines with 4WS
option only
109 ENGINE RPM
FAULT HIGH RPM
IS TOO LOW
When driving, engine
high RPM was too low Misadjust engine high
RPM to a value less than
3000 RPM and attempt
to drive This is a latched error.
Power or engine must be
cycled to clear error Machines with 4WS
option only
121 OPEN CIRCUIT
BRAKE (FWS C21)
A load of less than 70mA
was detected when
Brake (FWS C21) circuit
was energized Disconnect a wire from
Brake (FWS C21) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
122 SHORTED CIRCUIT
BRAKE (FWS C21)
Excessive load was
detected when Brake
(FWS C21) circuit was
energized Use a piece of wire to
short the Brake (FWS
C21) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
123 OPEN CIRCUIT
RS RET (FWS C22)
A load of less than 70mA
was detected when RS
Ret (FWS C22) circuit
was energized Disconnect a wire from
RS Ret (FWS C22) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
124 SHORTED CIRCUIT
RS RET (FWS C22)
Excessive load was
detected when RS Ret
(FWS C22) circuit was
energized Use a piece of wire to
short the RS Ret (FWS
C22) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
125 OPEN CIRCUIT
RS EXT (FWS C23)
A load of less than 70mA
was detected when RS
Ext (FWS C23) circuit
was energized Disconnect a wire from
RS Ext (FWS C23) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
126 SHORTED CIRCUIT
RS RET (FWS C23)
Excessive load was
detected when RS Ext
(FWS C23) circuit was
energized Use a piece of wire to
short the RS Ext (FWS
C23) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only
127 OPEN CIRCUIT
FS RET (FWS C24)
A load of less than 70mA
was detected when FS
Ret (FWS C24) circuit
was energized Disconnect a wire from
FS Ret (FWS C24) coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Machines with 4WS
option only