Haulotte Group 3522A, Operator'S Maintenance Manual

Page: 57 / 142

HAULOTTE GROUP 4 EQUIPMENT MAINTENANCE
57
TABLE 4-3 ERROR CODE DEFINITIONS
ERROR MESSAGE ERROR DEFINITION TO SIMULATE ERROR TO CLEAR ERROR COMMENTS
013 PRESSURE
SENSOR IS
DISCONNECTED
OR BAD
Pressure sensor output
is out of range Disconnect Pressure
Sensor This is a self clearing
error. When error
condition is corrected,
error is cleared Machines with Moment
Sense option only
014 CHECK ENGINE
LOW OIL
PRESSURE
Engine had low oil
pressure while running Kawasaki Engine: While
engine is running,
disconnect engine oil
pressure sense wire
Kubota Engine: While
engine is running,
disconnect engine oil
pressure sense wire and
connect wire to ground This is a latched error.
Power must be cycled to
clear error X-Boom Machines with
Kawasaki or Kubota
engines
015 MACHINE IS
NOT LEVEL
Machine has gone out of
level with use Tilt level sensor This is a self clearing
error. When error
condition is corrected,
error is cleared
016 LIFT BOOM A Boom Rotate, Extend
or Retract function has
been requested while
boom is down Try to Rotate, Extend or
Retract the boom while
boom is down This is a self clearing
error. When error
condition is corrected,
error is cleared
017 STOW BOOM An Outrigger function
has been requested
while boom is up Try to move an outrigger
while boom is up This is a self clearing
error. When error
condition is corrected,
error is cleared
018 LOSS OF LOAD
SENSE
COMMUNICATION
Lower Control has lost
RS485 communication
with Load Sense Module Remove Load Sense
Module from machine This is a latched error.
Power must be cycled to
clear error Machines with Load
Sense option only
019 BOOM FUNCTION
DISABLED
Load Sense Module has
detected an overloaded
boom and disabled boom
functions Overload Boom This is a latched error.
Power must be cycled to
clear error Machines with Load
Sense option only
020 LOSS OF LOAD
CELL CONNECTION
Load Sense Module has
lost connection with Load
Cell Disconnect Load Cell
from Load Sense Module This is a self clearing
error. When error
condition is corrected,
error is cleared Machines with Load
Sense option only
021 OPEN CIRCUIT
PRIMARY UP
A load of less than 70mA
was detected when
Primary Up circuit was
energized Disconnect a wire from
Primary Up coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
022 SHORTED CIRCUIT
PRIMARY UP
Excessive load was
detected when Primary
Up circuit was energized Use a piece of wire to
short the Primary Up coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
023 OPEN CIRCUIT
PRIMARY DOWN
A load of less than 70mA
was detected when
Primary Down circuit was
energized Disconnect a wire from
Primary Down coil This is a latched error.
Power must be cycled to
clear error Checked only at power up
Articulating Boom Models
024 SHORTED CIRCUIT
PRIMARY DOWN
Excessive load was
detected when Primary
Down circuit was
energized Use a piece of wire to
short the Primary Down
coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Articulating Boom Models
025 OPEN CIRCUIT
SECONDARY UP
A load of less than 70mA
was detected when
Secondary Up circuit was
energized Disconnect a wire from
Secondary Up coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Articulating Boom Models
026 SHORTED CIRCUIT
SECONDARY UP
Excessive load was
detected when
Secondary Up circuit was
energized Use a piece of wire to
short the Secondary Up
coil This is a latched error.
Power must be cycled to
clear error Checked only at
power up
Articulating Boom Models