manualshive.com logo in svg

Harman Martin VDO Fatron 20, User Manual

Share
Download
Harman Martin VDO Fatron 20 User Manual Download Page 43

DMX protocols

 43

Pre-programmed FX

Select the FX in this table on channel 5 in Basic, Segment or Pixel Mode. 

Set FX modification (in most cases this adjusts FX speed) on channel 6. 

Synchronize and set offsets between fixtures on channel 7.

Channel

DMX Value

Function

5

0

1
2
3
4
5
6
7
8
9

10
11
12
13
14
15
16

17 - 19

20
21
22
23

24 - 29

30
31

32 - 50

51
52
53
54
55
56
57
58
59
60
61
62

63 - 68

69
70
71
72
73
74
75
76
77
78

No FX

Intensity FX

Wave
Step
Pulse
Blackout strobe
2x strobe
3x strobe
4x strobe
Up, down, flash
Up, flash, down, flash
Random levels
Pixel killer
Noise overlay
Build up / down (random pixels added, then turned off)
In-out wave (crossfade between inner and outer pixels)
In-out step (step between inner and outer pixels)
In-out pulse (pulse inner pixels - wait - pulse outer pixels - wait)

No function (reserved for future use)

Movie flicker
Electric arc
Atomic lightning
Thunderstorm

No function (reserved for future use)

Random chase (quarter of pixels)
Water drop (intensity ripple from inner to outer pixels)

No function (reserved for future use)

Color FX

Rainbow wave
Rainbow step
Rainbow pulse
RGB wave
RGB step
RGB pulse
CMY wave
CMY step
CMY pulse
Random mix wave
Random mix step
Random mix pulse

No function (reserved for future use)

Solid
Spectrum shifter
RGB to white wave
RGB to white step
RGB to white pulse
RGB to white strobe
Normal to white wave
Normal to white step
Normal to white pulse
Normal to white strobe

Table 13: Pre-programmed FX

www.audiovias.com

Summary of Contents for Martin VDO Fatron 20





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands