manualshive.com logo in svg

Harman Martin VDO Fatron 20, User Manual

Share
Download
Harman Martin VDO Fatron 20 User Manual Download Page 31

System installation

 31

To create a DMX-controlled installation that draws DC power from the Martin® IP66 PSU 240W external 
power supply unit:

1. See Figure 18 on page 28 for an overview of this type of installation

2. Make sure that no devices in the installation can be connected to AC mains power until all installation 

work is complete.

3. Read “Safety information” on page 7 and “Precautions to avoid damage” on page 11.

4. Connect VDO Fatron fixtures together in chains either directly using the fixtures’ cable tails and BBD 

connectors or by adding Martin® hybrid cables with BBD connectors (see “BBD extension cables” on 
page 47).

Warning! 

Do not exceed the maximum total length of fixtures and total cable length per chain given in 

“Safety limits for connecting devices” on page 8.

5. If necessary to protect from water, dirt, etc., install blanking caps (see “Connectors” on page 48) on the 

output connectors of the last fixtures on the chain. There is no need to install DMX termination plugs, as 
fixtures have integral DMX termination.

6. See Figure 19. Connect a Martin® 5-pin male XLR female and male Martin® IP66 PSU 240W to female 

BBD adapter cable (P/N 91616050) to the start of each chain.

• Connect the 5-pin male XLR connector on the adapter cable to a DMX link that carries a DMX signal 

from an RDM-compliant DMX controller such as the Martin® M1 or M-PC.

• Connect the male Martin® IP66 PSU 240W connector on the adapter cable to the DC output of a 

Martin® IP66 PSU 240W.

• Connect the female BBD connector on the adapter cable to the male BBD connector at the start of the 

chain of VDO Fatron fixtures.

 

7. Install a mains power cable on the Martin® IP66 PSU 240W and connect it to AC mains power.

8. Apply AC mains power to the DMX controller.

You can now configure the system. See ”System setup”on page 34.

Figure 21: Martin® IP66 PSU 240W and DMX connections to a VDO Fatron chain

DC power input from

To chain of

fixtures

5-pin male XLR

Female BBD

XLR5+Martin® IP66 PSU 240W to BBD Input Cable, 0.25 m, P/N 91616050

Martin® IP66 PSU 240W

DMX from DMX/RDM

controller

Tripix system

connector

connector

www.audiovias.com

Summary of Contents for Martin VDO Fatron 20





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands