manualshive.com logo in svg

Harman Martin VDO Fatron 20, User Manual

Share
Download
Harman Martin VDO Fatron 20 User Manual Download Page 14

 14

VDO Fatron™ Family Safety and Installation Guide

Physical installation

Warning! Read “Safety information” on page 7 and “Precautions to avoid damage” on page 11 on 
before installing the VDO Fatron. Read this chapter for important information about installation 
safety.

Different installation methods and hardware are required depending on size of fixture, orientation, 
number of fixtures fastened together and conditions in the installation location: (a) indoors on a 
static structure or (b) in a location that is exposed to wind, vibration or other forces. Read this 
chapter carefully before installing VDO Fatron fixtures and use the method that is suitable for the 
installation site.

The VDO Fatron can be installed in any orientation. The most evenly matched optical characteristics when 
viewing an installation from the side at an angle are obtained when all VDO Fatron fixtures are oriented 
vertically, but unevenness will hardly be noticeable in horizontal strips, and then only when viewed from the 
side.

Allow free airflow and at least 10 mm (0.4 in.) of clearance around the product. Check that the product will 
not be exposed to direct sunlight or heat from other lighting, for example.

The VDO Fatron is designed to withstand low-pressure water projections but is not designed for permanent 
installation in wet locations. Do not submerge it or expose it to high-pressure water jets. If you need to 
create a permanent installation in a wet location, consider using the Exterior Pixline™ range of products 
from Martin®.

A small amount of water may enter and be visible between the clip-on optical cover (diffuser) and the fixture 
– this is normal and can be ignored, but remove the cover and wipe the fixture and cover dry before storage.

Wind precautions

Wind can create a risk of serious or lethal injury and damage due to falling fixtures. Follow the 
instructions in this chapter carefully.

If fixtures are to be installed in a location where they can be exposed to wind force, take these precautions:

• Observe all locally applicable laws, regulations and codes regarding safety of structures and installations.

• Suspend fixtures from a structure that is capable of holding the fixtures securely without any safety risk 

when fixtures are exposed to wind pressure.

• Ensure that weather forecasts and local wind speed are constantly monitored while the installation is in 

place.

• Ensure that all fixtures are removed from the installation immediately if constant or gusting wind speed 

exceeding Force 8 on the Beaufort scale (74 km/h, 46 mph or 20 meters/sec.) is forecast or present.

• Follow the instructions in this chapter for installing in locations that are exposed to wind. A location that is 

exposed to wind is not a stable location as defined in this manual.

www.audiovias.com

Summary of Contents for Martin VDO Fatron 20





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands