manualshive.com logo in svg

Harman Martin VDO Fatron 20, User Manual

Share
Download
Harman Martin VDO Fatron 20 User Manual Download Page 12

 12

VDO Fatron™ Family Safety and Installation Guide

light again when its temperature has fallen to a safe level. To avoid blackouts due to thermal shutdowns, 
we therefore recommend that you activate Thermal Throttling.

• When using DMX control, VDO Fatron fixtures automatically begin to reduce their light output when the 

ambient temperature reaches 45° C in order to control their internal temperature. Output is reduced 
gradually as the ambient temperature rises above 45° C. Fixtures will still light at the maximum ambient 
temperature of 55° C, but output will be considerably reduced. This feature avoids blackouts due to 
protective thermal shutdowns.

Flightcases

See below. For convenience and protection, we recommend that you use the flightcases and flightcase 
extenders available from Martin® for the VDO Fatron. See “Accessories” on page 47.

The VDO Fatron Flightcase accepts 5 x 1000 mm VDO Fatron fixtures or 15 x 320 mm fixtures. The VDO 
Fatron Flightcase Extender accept an additional 5 x 1000 mm VDO Fatron fixtures or 15 x 320 mm fixtures.

Figure 1: VDO Fatron flightcase accessories

VDO Fatron Flightcase

VDO Fatron Flightcase Extender

www.audiovias.com

Summary of Contents for Martin VDO Fatron 20





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands