manualshive.com logo in svg

Harman Martin VDO Fatron 20, User Manual

Share
Download
Harman Martin VDO Fatron 20 User Manual Download Page 38

 38

VDO Fatron™ Family Safety and Installation Guide

Service and maintenance

Warning! Read “Safety information” on page 7 and “Precautions to avoid damage” on page 11 
before carrying out service on the VDO Fatron.

Warning! Isolate the installation from AC mains power before servicing. 

Warning! Refer any service operation not described in this manual to a qualified service technician.

Important! Excessive dirt buildup causes overheating and may damage the product. Damage 
caused by inadequate cleaning is not covered by the product warranty.

The user will need to clean the VDO Fatron periodically. All other service operations on the VDO Fatron 
must be carried out by Martin Professional or its approved service agents.

Installation, on-site service and maintenance can be provided worldwide by the Martin Professional Global 
Service organization and its approved agents, giving owners access to Martin’s expertise and product 
knowledge in a partnership that will ensure the highest level of performance throughout the product’s 
lifetime. Please contact your Martin® supplier for details.

Cleaning

Cleaning schedules vary greatly depending on the operating environment. It is therefore impossible to 
specify precise cleaning intervals for the VDO Fatron. In extreme cases, the product may require cleaning 
after surprisingly few hours of operation. Environmental factors that may result in a need for frequent 
cleaning include:

• Use of smoke or fog machines.

• High airflow rates (near air conditioning vents, for example).

• Presence of cigarette smoke.

• Airborne dust (from stage effects, building structures and fittings or the natural environment in outdoor 

locations, for example).

If one or more of these factors is present, inspect products soon after installing them to see whether 
cleaning is necessary. Check again at frequent intervals. This procedure will allow you to assess cleaning 
requirements in your particular situation. If in doubt, consult your Martin® dealer about a suitable 
maintenance schedule.

To clean the product, use low-pressure compressed air to gently remove dust and loose particles from the 
front and back of the product. Wipe clean with a soft cloth dampened in a detergent solution. Do not use 
solvents or abrasives.

LED performance

At Martin® we use the best components available, but the characteristics of all LEDs change gradually over 
many thousands of hours of use. Not all colors change at the same rate, and rates of change vary 
depending on factors such as temperature and how intensively a particular color is used. Because of the 
changes, overall light output and the exact hues obtained from specific color mixes in all LED-based 
products can be expected to shift slightly over time.

Installing new software

It may be necessary to upload new software (i.e. device firmware) to the VDO Fatron if it appears to have a 
software-related fault or if you want to update to a newer software version.

Software for Martin® products is available from the Martin® website. The VDO Fatron software can be 
installed from the P3 System Controller over the P3 data link. You will need a Martin® P3 PowerPort 1500 or 
a Martin® P3 PowerPort 1000 IP for this. See the P3 System Controller user manual for software installation 
instructions.

www.audiovias.com

Summary of Contents for Martin VDO Fatron 20





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands