manualshive.com logo in svg

Harman Martin VDO Fatron 20, User Manual

Share
Download
Harman Martin VDO Fatron 20 User Manual Download Page 36

 36

VDO Fatron™ Family Safety and Installation Guide

Using the VDO Fatron

Warning! Read “Safety information” on page 7 and “Precautions to avoid damage” on page 11 on 
before applying power to the VDO Fatron.

Do not use the VDO Fatron if the ambient temperature exceeds 45° C (113° F) or falls below -20° C (-4° F).

P3 display

The VDO Fatron can display video from all common video sources. The video signal must be sent to a 
Martin® P3™ controller and then distributed to fixtures. The P3™ controller lets you map, configure and 
control an installation containing VDO Fatron fixtures (and other Martin® P3™ video display products if you 
have them). See the P3 controller documentation for details.

DMX control

The VDO Fatron can display effects controlled by DMX. Using DMX control, each pixel consists of a 2x2 
square of LEDs.

Three DMX modes are available:

•

RGB mode

 uses three DMX channels and gives RGB color mixing of all the pixels on a fixture.

•

Basic mode

 uses ten DMX channels and gives RGB color mixing, strobe effects and pre-programmed FX 

(dynamic effects).

•

Segment mode

 uses the first seven DMX channels of Basic mode plus three channels per segment for 

segment-level RGB color mixing, strobe effects and pre-programmed FX. 320 mm fixtures are divided into 
4 segments, 1000 mm fixtures are divided into 10 segments.

•

Pixel mode

 uses the first seven DMX channels of Basic mode plus three channels per pixel for pixel-level 

RGB color mixing, strobe effects and pre-programmed FX.

See “DMX protocols” on page 40 for full details of DMX control.

An RDM-compatible controller is required so that you can address and configure the fixtures. See the 
DMX/RDM controller documentation for details.

Magnetic ‘control button’

A magnetic sensor is embedded inside the VDO Fatron 
behind the label on the back of the fixture (see 

C

 in Figure 

2 on page 13). The sensor acts as a control button. To 
activate the sensor, swipe a magnet past it. 

We recommend that you use the Martin® VDO Test and 
Accessory Tool (see “Accessories” on page 47), which 
contains a magnet.

Activating the magnetic sensor lets you display the 
product’s status, test the LEDs and reset the VDO Fatron.

Figure 24: VDO Test and Accessory Tool

www.audiovias.com

Summary of Contents for Martin VDO Fatron 20





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands