manualshive.com logo in svg

Harman Martin VDO Fatron 20, User Manual

Share
Download
Harman Martin VDO Fatron 20 User Manual Download Page 24

 24

VDO Fatron™ Family Safety and Installation Guide

Installing and removing optical accessories

The VDO Fatron must be used with an 
optical accessory (diffuser or lens) 
installed on the front of the fixture. A 
wide range of these accessories is 
available from Martin® (see 
“Accessories” on page 47). They clip 
onto the front of fixtures and can be 
installed and removed in seconds.

To aid removal of optical accessories, 
we recommend that you use one of the 
two solutions available from Martin® for 
the VDO Fatron: either the Magnetic 
Swiper Test Tool or the Lens Removal 
Jaws that can be clipped onto 
extra-wide opening pipe grips. See 
“Accessories” on page 47.

To install an optical accessory:

1. Block access below the work area and work from a stable platform.

2. See Figure 14. Push one side of the diffuser / lens into the front of the fixture, then push the other side 

down also (see 

A

) so that both sides clip into place.

To remove an optical accessory:

1. Block access below the work area and work from a stable platform.

2. Grasp the diffuser with pipe grips and the jaws available from Martin®, or press the lever ends of two 

Magnetic Swiper Test Tools (see 

B

 in Figure 14) between one side of the diffuser / lens and the fixture. 

Lift the diffuser out of its clip and away from the fixture.

Securing optical accessories with locking screws

See Figure 15. Optical accessories (diffusers and lens arrays) are 
secured on the front of the fixture with four M3x6 hex socket 
headless set screws (Allen grub screws), two screws at each end 
of the fixture. The screws sit in channels in the fixture profile and 
engage in cutouts in the back of optical accessories, locking the 
accessory laterally to prevent it from sliding.

If you replace the optical accessory on a product, check that the 
accessory clips correctly into the front of the fixture and check that 
it is held between the four screws. You can adjust the screws with a 
hex wrench (Allen key) if necessary, but do not overtighten. Tighten 
screws just until you feel resistance and check that the accessory 
does not have any sideways play.

Figure 14: Installing and removing a diffuser

B

A

Figure 15: Optical accessory 

locking screws

www.audiovias.com

Summary of Contents for Martin VDO Fatron 20





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands