HappyJapan HCD3, Instruction Book

Page: 3 / 251

-D3 -5
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ... 1-1
WARNING LABELS & THEIR LOCATIONS ..... 1-2
SETTING UP THE MACHINE
Assemble machine unit ........................... 2-1
How to carry machine ............................. 2-2
Machine installation ................................ 2-3
Assemble safety sensor (Option) ...................... 2-4
Assemble table (Option) ......................... 2-5
Assemble border frame (Option) ............2-5b
Assemble bobbin thread guide (Option) 2-6
Grounding instruction (for type of 120V) 2-7
Disposal of a battery ..............................2-7
MAIN PARTS ............................................. 3-1
THE CONTROL BOX ................................ 3-3
DRIVE MODE .................................. 3-4
MENU ................................................... 3-A
INSERTING A NEEDLE ............................. 4-1
SELECT NEEDLES AND THREADS ....... 4-2
BACKING MATERIALS ............................. 4-3
BORDER FRAME CLIP ............................. 4-3a
WINDING
Winding the bobbin (Option) ................... 4-4
Removing the bobbin .............................. 4-5
Inserting the bobbin ................................ 4-5
Adjusting bobbin thread tension .............. 4-5
Inserting the bobbin case ........................ 4-5
THREADING THE MACHINE
How to thread upper thread .................... 4-6
HOW TO READ THESE INSTRUCTIONS, SCROLLBAR ... 4-8
DISPLAYING THE PATTERN IN SETTING MODE ... 4-9
TURNING THE MACHINE ON
How to turn on the machine .................... 5-1
Calendar and clock setting ...................... 5-2
MESSAGES .............................................. 5-3
PREPARATION OF PATTERN DATA
Connecting to a PC ................................. 5-4
Reading embroidery pattern data from the PC . 5-4b
Reading embroidery pattern data ........... 5-5
Selection of folders ................................. 5-9
How to select patterns from memory ... 5-A
Erasing patterns from memory .............. 5-B
NEEDLE BAR SELECTION .................... 5--E
SEWING WITH TUBULAR FRAMES
Installing and removing the frame base .. 6-1
How to hoop ............................................ 6-2
Mounting the hoop on the machine ......... 6-3
Starting to embroider .............................. 6-4
CAP FRAME (option)
Cap frame settings .................................. 7-1
Installing and removing the cap drive frame ...7-2
Normal cap frames .................................. 7-5
Wide cap frames ..................................... 7-8
Starting to embroider ........................... 7-B
ADJUSTING THE THREAD TENSION ..... 8-1
ADJUSTING THE LASER POINTER (OPTION) .. 8-2
BORER (Option) ........................................ 8-4
SEWING
What to do if the thread breaks while sewing 9-1
Stopping and resuming sewing ............... 9-1
Loss of power while embroidering .......... 9-2
Moving the hoop while embroidering and then returning to
the correct location (Position) ............................. 9-3
Moving back to the starting point (Origin) 9-3
Going back to the beginning of the design (Top) ... 9-4
Placing the design in the center of the selected
embroidery frame (Center) ........................... 9-4
Rotating and mirroring designs (Convert) ..... 9-5
Starting in the middle of a design (Position) ...9-6
POSITION ALIGNMENT BY DEFINING 2 POINTS .. 9-8
POSITION ................................................. 9-B
Piece number ..........................................9-C
Bobbin thread alarm ..............................9-Cb
REGISTER ................................................9-D
Entry ........................................................9-E
Return .....................................................9-F
READING
Join ....................................................... 10-1
Pattern read settings ............................. 10-3
0_1 RC01
0-1