manualshive.com logo in svg

Haier GE NS18HM, Service Manual, Page: 82 / 86

Share
Download
Haier GE NS18HM Service Manual Download Page 82

Page  82

31-5000751   Rev. 0

GF= Gas Furnace, AH=Air Handler, ID=Indoor unit (GF or AH), HP=Heat Pump, AC=Air Conditioner, OD=Outdoor Unit (AC or HP), ZA=Zone system and TS=Thermostat

Alert 

Code

Inverter 

Code

Inverter Flash 

Code

Priority 

Condition

Actual Displayed 

Alert Text

Component or System Operational State and Troubleshooting 

Tip

How to Clear Alert 

Code

Red 

LED

Green 

LED

441

14

1 flash

4 

flashes

Information 

Only-Dealer

OD Inverter 

Compressor 

Slowdown - High 

Compressor 

Current

This alert code is for more information than an issue with the system.

• 

When the inverter gets close to the current or heat sink temperature 

limit,  it  will  limit  the  ramp  rate.  Instead  of  changing  compressor 

speed at 1 hz/second, it changes to 5 hz/20 seconds.

• 

Compressor slowdown due to high compressor current.

• 

Compressor current is approaching limit. 

• 

The compressor speed automatically slows. 

• 

This error code is primarily for informational purposes as the inverter 

controls the compressor to operate within design parameters. Alert 

code  441  typically  occurs  at  startup  as  the  compressor  current 

increases rapidly during startup.

• 

The inverter will reduce the compressor speed by 4 Hz and slow the 

compressor ramp up speed to the requested compressor demand 

speed  (capacity).  This  is  normal  and  expected  operation  of  the 

inverter  to  control  the  inverter  within  design  parameters.  In  most 

cases the alert code 441 notification does not require any additional 

service or diagnostic procedures.

• 

The control sets indoor CFM and outdoor RPM to values according 

to demand percentage rather than the actual Hz. 

• 

Possible issue is system running at high pressures. 

• 

Check for high pressure trips or other alert codes in thermostat and 

outdoor control.

• 

Inverter LEDs will flash code 14.

• 

Refer to the unit service documentation for detailed troubleshooting 

procedures.

Inverter flash code 14. 

The sequence is:

• 

Red LED: One Flash

• 

Green LED: Four Flashes

NOTE:  

Inverter normal operations with no error code present is as 

follows. Red LED is ON and green LED is OFF.

Automatically clears 

when the condition 

no longer exists.

Table 24. Outdoor Control 7-Segment Display Alert Codes and Inverter LED Flash Codes

Summary of Contents for GE NS18HM























































































Reviews:

No comments