Haier GE NS18HM Service Manual Download Page 13 | Manualshive

Page: 13 / 86

Haier GE NS18HM Service Manual Download Page 13

Page 13

31-5000751 Rev. 0

Tonnage

Liquid Line

SIze

Total Linear Length (ft.)

25

50

75

100

125

150

-24

3/8”

25

50

60

60

60

60

Max Elevation (ft)

-36

3/8”

25

50

60

56

51

45

1/2”

25

50

60

60

60

60

-48

3/8”

25

50

50

41

31

22

1/2”

25

50

60

60

60

60

-60

3/8”

25

50

36

22

8

NR

1/2”

25

50

60

60

60

59

NOTE: Shaded rows indicate rated liquid line size.
A. Find your tonnage on the left side of the table.
B. Start with the rated liquid line size (shaded row) on the outdoor tonnage.
C. Select the actual Total Linear Length of your system shown at the top of the table.
D. The elevation listed in the table is the maximum allowed for the liquid line listed.
E. Select or consider the larger liquid line size shown in the table if the elevation does not meet your requirements.

Table 5. Liquid Line Diameter Selection

Typical Existing Expansion Valve Removal

Procedure

SENSING

LINE

TWO-PIECE PATCH PLATE

(UNCASED COIL ONLY)

VAPOR

LINE

DISTRIBUTOR

ASSEMBLY

DISTRIBUTOR

TUBES

LIQUID

LINE

MALE EQUALIZER

LINE FITTING

EQUALIZER

LINE

EXPANSION

VALVE

TEFLON®

RING

STUB END

TEFLON

®

RING

SENSING BULB

LIQUID LINE

ORIFICE

HOUSING

LIQUID LINE

ASSEMBLY WITH

BRASS NUT

Figure 7. Remove Expansion Valve

(Uncased Coil Shown)

1.

On fully cased coils, remove the coil access and

plumbing panels.

2.

Remove any shipping clamps from the liquid line and

distributor assembly.

3.

Disconnect the equalizer line from the fitting on the

vapor line.

4.

Remove the vapor line sensing bulb.

Typical Existing Fixed Orifice Removal

Procedure

TEFLON

®

RING

FIXED ORIFICE

BRASS NUT

LIQUID LINE ASSEMBLY

(INCLUDES STRAINER)

LIQUID LINE ORIFICE HOUSING

DISTRIBUTOR TUBES

DISTRIBUTOR

ASSEMBLY

REMOVE AND DISCARD

WHITE TEFLON

®

SEAL

(IF PRESENT)

Figure 6.

Remove Fixed Orifice

(Uncased Coil Shown)

1.

On fully cased coils, remove the coil access and

plumbing panels.

2.

Remove any shipping clamps from the liquid line and

distributor assembly.

3.

Using two wrenches (one to hold the orifice housing

and one to remove the brass nut), disconnect liquid

line from liquid line orifice housing. Take care not to

twist or damage distributor tubes during this process.

4.

Remove and discard fixed orifice, valve stem assembly

(if present) and Teflon

®

washer, as shown in Figure 6.

5.

Use a field-provided fitting to temporarily reconnect the

liquid line to the indoor unit’s liquid line orifice housing.

«
...
11
12
13
14
15
...
»

Summary of Contents for GE NS18HM























































































Reviews:

No comments