manualshive.com logo in svg

Haier GE NS18HM, Service Manual, Page: 38 / 86

Share
Download
Haier GE NS18HM Service Manual Download Page 38

Page  38

31-5000751   Rev. 0

GF= Gas Furnace, AH=Air Handler, ID=Indoor unit (GF or AH), HP=Heat Pump, AC=Air Conditioner, OD=Outdoor Unit (AC or HP), ZA=Zone system and TS=Thermostat

Alert 

Code

Inverter 

Code

Inverter Flash 

Code

Priority 

Condition

Actual Displayed 

Alert Text

Component or System Operational State 

and Troubleshooting Tip

How to Clear 

Alert Code

Red 

LED

Green 

LED

434

53

5 

flashes

3 

flashes

Service 

Soon/

Service 

Urgent

OD Inverter 

Comm Error to 

Main Control

• 

Outdoor control has lost communications with the inverter continuously 

during a single thermostat call and one hour period. 

• 

Outdoor control will stop all compressor demands – moderate condition.

• 

Indoor blower will stop functioning. 

NOTE:  

Indoor blower will not run in test mode either when alert code 434 

is active. Only after system reset will it operate.

• 

This alert code will occur if the outdoor unit power is turned off and the 

indoor  unit  power  (24VAC  to  GE Appliances  outdoor  control)  remains 

on,  or  if  the  indoor  unit  power  is  turned  off  (24VAC  to  GE Appliances 

outdoor control) and the outdoor unit power is on. This could occur while 

performing service or maintenance procedures on the indoor or outdoor 

unit.

• 

The  GE  Appliances  outdoor  control  will  attempt  to  re-establish 

communication to the inverter when the alert code 434 occurs by cycling 

the  outdoor  unit  contactor  off  for  two  minutes.  Upon  energizing  the 

contactor the GE Appliances outdoor control will attempt to communicate 

to the inverter for three minutes. This process will be repeated three times 

in attempt to establish communication before locking out. 

• 

If the unit is locked out with a critical alert code 434, reset the system by 

cycling the outdoor unit power off and back on. Then cycle the indoor 

power off (24VAC to the GE Appliances outdoor control) and then back 

on.

• 

If this condition continuously occurs during a one hour period and during 

a single thermostat call, the outdoor unit will lock out and display alert 

code 434 – critical condition. 

Troubleshooting Options:

• 

Check for loose or disconnected electrical connections. 

• 

Interruption of main power to inverter. 

• 

Inverter LEDs will flash code 53.

• 

Refer  to  the  unit  service  documentation  for  detailed  troubleshooting 

procedures.

Inverter flash code 53.

The sequence is:

• 

Red LED: Five Flashes

• 

Green LED: Three Flashes

NOTE:  

Inverter  normal  operations  with  no  error  code  present  is  as 

follows. Red LED is ON and Green LED is OFF

Automatically clears 

when the system 

detects that the 

issue no longer 

exists.
If the unit is locked 

out with a critical 

alert code 434, reset 

the system by first 

cycling the outdoor 

unit power off and 

back. Then cycle 

the indoor power off 

(24VAC to the GE 

Appliances outdoor 

control) and then 

back on.

435

60

6 

flashes

OFF

Service 

Urgent

OD Inverter 

EEPROM 

Checksum fault

Inverter internal error.

• 

When this error occurs, the outdoor control will cycle power to the inverter 

by opening the contactor for two minutes – moderate condition.

• 

Outdoor  control  will  cycle  power  to  the  inverter  three  times  and  then 

outdoor unit is locked out – critical condition.

• 

Inverter LEDs will flash code 60.

• 

Refer  to  the  unit  service  documentation  for  detailed  troubleshooting 

procedures.

Inverter flash code 60. 

The sequence is:

• 

Red LED: Six Flashes

• 

Green LED: Off

NOTE:  

Inverter  normal  operations  with  no  error  code  present  is  as 

follows. Red LED is ON and Green LED is OFF.

To clear alert code 

disconnect power 

to outdoor unit and 

restart.

Table 12. Alert Codes and Troubleshooting

Summary of Contents for GE NS18HM























































































Reviews:

No comments