manualshive.com logo in svg

Haier GE NS18HM, Service Manual, Page: 65 / 86

Share
Download
Haier GE NS18HM Service Manual Download Page 65

Page  65

31-5000751   Rev. 0

The NS18HM models with a rotary compressor do not have a factory installed liquid filter drier and it is not required on these 

models.  A liquid line filter drier on the rotary compressor models may be field installed if desired.

FIGURE 36. Liquid Line Filter Drier

Top Cap Switch Operation, Checkout and Status / Error Codes

OPERATION:

Top Cap Thermal Sensor Switch (S173)

Some units are equipped with a compressor-mounted normally closed temperature switch that prevents compressor damage 

due to overheating caused by internal friction. The switch is located on top of the compressor casing. This switch senses 

the compressor casing temperature and opens at 239-257°F to shut off compressor operation. The auto-reset switch closes 

when the compressor casing temperature falls to 151-187°F, and the compressor is re-energized. This is a single-pole, 

single-throw (SPST) bi-metallic switch.

TOP OF COMPRESS0R

SWITCH COVER

COMPRESSOR TOP CAP SWITCH

(SPST BI-METALIC SWITCH,

NORMALLY OPENS AT 239-257ºF,

AND CLOSES AT 151-187ºF

FIGURE 37. Top Cap Thermal Sensor Switch

CHECKOUT:

Using a multimeter set to ohms, with the terminals disconnected from the system, check the resistance between the two 

terminals of the top cap switch. If the meter display does not change, the switch is open. If the meter display goes to infinite, 

the switch is closed.

FIGURE 38. Verifying Top Cap Thermal Sensor Switch

STATUS:

None

Summary of Contents for GE NS18HM























































































Reviews:

No comments