manualshive.com logo in svg

Haier GE NS18HM, Service Manual, Page: 37 / 86

Share
Download
Haier GE NS18HM Service Manual Download Page 37

Page  37

31-5000751   Rev. 0

GF= Gas Furnace, AH=Air Handler, ID=Indoor unit (GF or AH), HP=Heat Pump, AC=Air Conditioner, OD=Outdoor Unit (AC or HP), ZA=Zone system and TS=Thermostat

Alert 

Code

Inverter 

Code

Inverter Flash 

Code

Priority 

Condition

Actual Displayed 

Alert Text

Component or System Operational State 

and Troubleshooting Tip

How to Clear 

Alert Code

Red 

LED

Green 

LED

433

29

2 

flashes

9 

flashes

Service 

Soon/

Service 

Urgent

OD Inverter 

Compressor 

Over-current

Compressor phase current is too high.

• 

During initial startup, a six minute time delay is implement to prevent the 

alarm from occurring.

• 

Error  occurs  when  compressor  peak  phase  current  is  greater  than  28 

amps. 

• 

Inverter will issue inverter code 14 first and slow down to try to reduce 

the current. 

• 

If the current remains high, outdoor unit will stop (compressor and fan) – 

moderate condition.

• 

Cycle timer is initiated.

• 

If condition occurs five times within 60 consecutive minutes, the system 

will lockout – critical condition.

• 

This alert code may be triggered by the inverter or the GE Appliances  

variable capacity outdoor (inverter controlled) unit.

• 

GE  Appliances  outdoor  control  may  trigger  an  this  alert  code  if  the 

inverter reduces the compressor speed which is identified as a alert code 

441 and the compressor speed (in hz) is below the minimum speed. This 

will typically occur at start-up. The inverter automatically increases the 

compressor minimum speed below 45ºF in the heating mode and above 

115ºF ensure the compressor capacity is sufficient for oil return. If alert 

code 433 occurs and inverter does not indicate an inverter code 29, the 

GE Appliances outdoor control triggered the alert code 433.

• 

Inverter LEDs will flash code 29.

• 

Refer  to  the  unit  service  documentation  for  detailed  troubleshooting 

procedures.

Inverter flash code 29. 

The sequence is:

• 

Red LED: Two Flashes

• 

Green LED: Nine Flashes

NOTE:  

Inverter  normal  operations  with  no  error  code  present  is  as 

follows. Red LED is ON and Green LED is OFF.

To clear alert code 

disconnect power 

to both the indoor 

and outdoor units 

and then reconnect 

power. Restart 

system.

Table 12. Alert Codes and Troubleshooting

Summary of Contents for GE NS18HM























































































Reviews:

No comments