manualshive.com logo in svg

Haier GE NS18HM, Service Manual, Page: 25 / 86

Share
Download
Haier GE NS18HM Service Manual Download Page 25

Page  25

31-5000751   Rev. 0

4. 

The unit will display the unit type for 10 seconds. Press 

the push button and hold it for 3 seconds for the unit 

to  store  the  unit  type.  Once,  the  unit  code  is  stored 

the  system  acknowledges  by  displaying  a  string  of 

characters ending with the updated system unit code.

After programming of unit type is complete, the unit can be 

set up for charge mode operation.

Charge Mode Jumper

To  initiate  the  NS18HM  Charge  Mode  function,  install 

the  jumper  across  the  two  Charge  Mode  Pins  (CHRG 

MODE) on the outdoor control. The Charge Mode can be 

used when charging the system with refrigerant, checking 

the  refrigerant  charge,  pumping  down  the  system  and 

performing other service procedures that requires outdoor 

unit operation at 100% capacity.

NS18HM Charge Mode Operation with a Conventional 

24VAC Heat Pump Thermostat

Charge Mode Display String

When  unit  is  in  the  charge  mode,  Suction  Pressure 

(SPxxx), Suction Temp (Stxx.x), Superheat (SHxx.x), Liquid 

Pressure  (LPxxx),  Liquid  Temp  (Ltxx.x)  and  Subcooling 

(SCxx.x) will be scrolled on the 7-segment display.

Example:

S P 1 3 5

 pause 

S t 6 2

 pause 

S H 1 5

 pause 

L P 3 4 5 

pause 

L t 9 6

 pause 

S C 1 0

 repeat

Charge Mode Jumper Operation in the Cooling Mode

On  applications  with  a  conventional  24VAC  heat  pump 

thermostat,  the  charge  mode  jumper  must  be  installed 

on  the  Charge  Mode  Pins  after  providing  a  cooling 

compressor demand to the NS18HM and an “O” cooling 

reversing  valve  demand  to  initiate  the  Charge  Mode.  A 

cooling blower demand must also be provided to initiate 

blower in high stage operation on the indoor unit.

The compressor and outdoor fan motor will begin to ramp 

up and reach 100% design capacity within 3 minutes. They 

will continue to operate at 100% design capacity for the 

duration of charge mode. 

Charge Mode Jumper Operation in the Heat Pump 

Heating Mode

On  applications  with  a  conventional  24VAC  heat  pump 

thermostat, the charge mode jumper must be installed on 

the Charge Mode Pins after providing a heating compressor 

demand  to  the  NS18HM  without  an  “O”  reversing  valve 

signal  to  initiate  the  Charge  Mode.  A  heating  blower 

demand  must  also  be  provided  to  initiate  high  speed 

blower operation on the indoor unit. 

The compressor and outdoor fan motor will begin to ramp 

up and reach 100% design capacity within 3 minutes. They 

will continue to operate at 100% design capacity for the 

duration of charge mode. 

Exiting Charge Mode

To  exit  the  charging  mode,  remove  the  Charge  Mode 

Jumper  from  the  Charge  Mode  Pins.  The  system  will 

be  in  Charge  Mode  for  a  maximum  time  of  60  minutes 

and will automatically exit the charge mode and resume 

normal operation after 60 minutes even if the charge mode 

jumper is left in place. To extend the charge mode beyond 

60  minutes,  ensure  the  cooling/heating  demand,  blower 

demand  and  appropriate  reversing  valve  demand  are 

available and reapply the charge mode jumper. 

NOTE: 

If compressor demand is lost during charge mode 

period, then the compressor and fan will cease to operate, 

and  the  unit  will  enter  into  a  delay  timer  for  3  minutes. 

Repeat  the  charging  mode  procedure  to  get  back  into 

charge mode.

Cooling Operation Mode Jumper

The  Cooling  Operation  Mode  Jumper  is  only  used  on 

applications  installed  with  a  conventional  24VAC  heat 

pump  thermostat.  In  applications  with  a  conventional 

24VAC heat pump thermostat, the compressor capacity is 

controlled to maintain the target suction pressure setpoint. 

The Cooling Operation Mode Jumper has three selectable 

cooling modes. The three modes are Efficiency (Jumper 

installed on Pins 1 & 2), Normal Mode (Jumper installed 

on  Pins  2  &  3)  and  Comfort  Mode  (Jumper  Removed). 

The  factory  default  position  is  the  Efficiency  Mode.  The 

Efficiency mode has a variable suction pressure setpoint 

that will vary with the outdoor temperature; as the outdoor 

temperature  increases  the  suction  pressure  setpoint  will 

decrease.  When  the  Cooling  Operation  Mode  jumper 

is  installed  in  the  “Normal  Mode”  the  suction  pressure 

setpoint is 135 psig.

When the Cooling Operation Mode jumper is installed in 

the “Comfort Mode” the suction pressure setpoint is 125 

psig.

Operation Mode 

Jumper

Jumper 

Position

Target Suction 

Pressure Setting

Efficiency (default) Pin 1 to Pin 2

Variable based on OAT

Normal

Pin 2 to Pin 3

135 PSIG

Comfort

Jumper Off

125 PSIG

Table 9. Cooling Operation Mode Jumper 

(Conventional 24VAC Heat Pump Thermostats Only)

Summary of Contents for GE NS18HM























































































Reviews:

No comments