manualshive.com logo in svg

Haier GE NS18HM, Service Manual, Page: 79 / 86

Share
Download
Haier GE NS18HM Service Manual Download Page 79

Page  79

31-5000751   Rev. 0

GF= Gas Furnace, AH=Air Handler, ID=Indoor unit (GF or AH), HP=Heat Pump, AC=Air Conditioner, OD=Outdoor Unit (AC or HP), ZA=Zone system and TS=Thermostat

Alert 

Code

Inverter 

Code

Inverter Flash 

Code

Priority 

Condition

Actual Displayed 

Alert Text

Component or System Operational State and Troubleshooting 

Tip

How to Clear Alert 

Code

Red 

LED

Green 

LED

436

62

6 

flashes

2 

flashes

Service Soon/

Service 

Urgent

OD Inverter 

High Heat-Sink 

Temperature

Inverter heat sink temperature exceeded limit.

• 

This occurs when the heat sink temperature exceeds the inverter 

limit. Inverter will issue inverter alert code 13 first and slow down to 

try to cool the heat sink. 

• 

If temperature remains high, outdoor unit will stop both compressor 

and fan – moderate condition.

• 

Anti- short cycle is initiated. 

• 

If condition occurs five times within an hour, system will lockout – 

critical condition.

• 

The screws that hold the inverter to the inverter board were loose 

causing poor contact between these two components.

• 

Tighten screws that hold the heat sink to the inverter control board. 

NOTE:  

Wait  five  minutes  for  all  capacitors  to  discharge  before 

checking screws.

• 

Inverter LEDs will flash code 62.

• 

Refer to the unit service documentation for detailed troubleshooting 

procedures.

Inverter flash code 62. 

The sequence is:

• 

Red LED: Six Flashes

• 

Green LED: Two Flashes

NOTE:  

Inverter normal operations with no error code present is as 

follows. Red LED is ON and Green LED is OFF.

Moderate condition 

will automatically 

clear when the 

inverter sends an 

alert code clear 

message.
Critical condition 

is cleared by 

disconnecting power 

to the outdoor unit 

and restart.

437

65

6 

flashes

5 

flashes

Service Soon/

Service 

Urgent

OD Inverter Heat-

Sink temp Sensor 

Fault

Heat sink temperature sensor fault has occurred (temperature less 

than 4ºF or greater than 264ºF after 10 minutes of operation).

• 

When the temperature sensor detects a temperature less than 4ºF 

or greater than 264ºF after 10 minutes of operation. 

• 

Outdoor  unit  will  stop  both  compressor  and  fan  –  moderate 

condition.

• 

Anti-short cycle is initiated. 

• 

If condition occurs five times within an hour, system will lockout – 

critical condition.

• 

Inverter LEDs will flash code 65.

• 

Refer to the unit service documentation for detailed troubleshooting 

procedures.

Inverter flash code 65. 

The sequence is:

• 

Red LED: Six Flashes

• 

Green LED: Five Flashes

NOTE:  

Inverter normal operations with no error code present is as 

follows. Red LED is ON and Green LED is OFF.

Moderate priority 

condition will 

automatically clear 

when the inverter 

sends an alert code 

clear message.
Critical priority 

condition can 

be cleared by 

disconnecting and 

reconnecting power 

to outdoor unit to 

restart.

Table 24. Outdoor Control 7-Segment Display Alert Codes and Inverter LED Flash Codes

Summary of Contents for GE NS18HM























































































Reviews:

No comments