manualshive.com logo in svg

Haier GE NS18HM, Service Manual, Page: 60 / 86

Share
Download
Haier GE NS18HM Service Manual Download Page 60

Page  60

31-5000751   Rev. 0

GF= Gas Furnace, AH=Air Handler, ID=Indoor unit (GF or AH), HP=Heat Pump, AC=Air Conditioner, OD=Outdoor Unit (AC or HP), ZA=Zone system and TS=Thermostat

Alert 

Code

Inverter 

Code

Inverter Flash 

Code

Priority 

Condition

Actual Displayed 

Alert Text

Component or System Operational State and Troubleshooting Tip How to Clear Alert 

Code

Red 

LED

Green 

LED

430

26

2 

flashes

6 

flashes

Service Soon/

Service 

Urgent

OD Inverter 

Compressor 

Startup Fail

Compressor start-up failure.

• 

If condition is detected, outdoor unit will stop (compressor and fan) 

– moderate condition.

• 

Anti-short cycle is initiated. 

• 

If  condition  occurs  10  times  within  60  consecutive  minutes,  the 

system will lockout – critical condition.

• 

Inverter LEDs will flash code 26.

• 

Refer to the unit service documentation for detailed troubleshooting 

procedures.

Inverter flash code 26. 

The sequence is:

• 

Red LED: Two Flashes

• 

Green LED: Six Flashes

NOTE:  

Inverter normal operations with no error code present is as 

follows. Red LED is ON and Green LED is OFF.

• 

Check refrigerant

• 

Replace outdoor control board

• 

Replace inverter.

To clear, disconnect 

power to outdoor unit 

and restart.

433

29

2 

flashes

9 

flashes

Service Soon/

Service 

Urgent

OD Inverter 

Compressor 

Over-current

Compressor phase current is too high.

• 

During initial startup, a six minute time delay is implement to prevent 

the alarm from occurring.

• 

Error occurs when compressor peak phase current is greater than 

28 amps. 

• 

Inverter  will  issue  inverter  code  14  first  and  slow  down  to  try  to 

reduce the current. 

• 

If the current remains high, outdoor unit will stop (compressor and 

fan) – moderate condition.

• 

Cycle timer is initiated.

• 

If  condition  occurs  five  times  within  60  consecutive  minutes,  the 

system will lockout – critical condition.

• 

This alert code may be triggered by the inverter or the GE Appliances 

variable capacity outdoor (inverter controlled) unit.

• 

GE Appliances outdoor control may trigger an this alert code if the 

inverter reduces the compressor speed which is identified as a alert 

code 441 and the compressor speed (in hz) is below the minimum 

speed. This will typically occur at start-up. The inverter automatically 

increases  the  compressor  minimum  speed  below  45ºF  in  the 

heating mode and above 115ºF ensure the compressor capacity is 

sufficient for oil return. If alert code 433 occurs and inverter does not 

indicate an inverter code 29, the GE Appliances communicating GE 

Appliances outdoor control triggered the alert code 433.

• 

Inverter LEDs will flash code 29.

• 

Refer to the unit service documentation for detailed troubleshooting 

procedures.

Inverter flash code 29. 

The sequence is:

• 

Red LED: Two Flashes

• 

Green LED: Nine Flashes

NOTE:  

Inverter normal operations with no error code present is as 

follows. Red LED is ON and Green LED is OFF.

To clear alert code 

disconnect power to 

both the indoor and 

outdoor units and 

then reconnect pow

-

er. Restart system.

Table 19. Outdoor Control 7-Segment Display Alert Codes - Compressor

Summary of Contents for GE NS18HM























































































Reviews:

No comments