manualshive.com logo in svg

H3C WA Series, Layer 2 Command Reference, Page: 80 / 133

Share
Download
H3C WA Series Layer 2 Command Reference Download Page 80

 

72

 

Use 

undo stp root-protection

 to restore the default.  

By default, the root guard function is disabled.  
Among loop guard, root guard and edge port settings, only the first configured function takes effect on 

a port. 
Related commands: 

stp edged-port

 and 

stp loop-protection

. 

Examples 

# Enable the root guard function for GigabitEthernet 1/0/1.  

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] stp root-protection 

stp tc-protection 

Syntax 

stp tc-protection enable 
stp

 

tc-protection disable

 

View 

System view 

Default level 

2: System level 

Parameters 

None 

Description 

Use 

stp tc-protection enable

 to enable the TC-BPDU attack guard function for the device.  

Use 

stp tc-protection disable

 to disable the TC-BPDU attack guard function for the device.  

By default, the TC-BPDU attack guard function is enabled.  

Examples 

# Disable the TC-BPDU attack guard function for the device.  

<Sysname> system-view 

[Sysname] stp tc-protection disable 

stp tc-protection threshold 

Syntax 

stp tc-protection threshold 

number

 

undo stp tc-protection threshold 

View 

System view 

Summary of Contents for WA Series






































































































































Reviews:

No comments