H3C WA Series Layer 2 Command Reference Download

Page: 25 / 133

Description

Use

flow-interval

to set the statistics polling interval for all interfaces.

Use

undo flow-interval

to restore the default interval.

By default, the statistics polling interval is 300 seconds.

Examples

# Set the statistics polling interval to 100 seconds.

<Sysname> system-view

[Sysname] flow-interval 100

loopback-detection control enable

Syntax

loopback-detection control enable
undo loopback-detection control enable

View

Layer 2 Ethernet interface view

Default level

2: System level

Parameters

None

Description

Use

loopback-detection control enable

to enable loopback detection control on trunk or hybrid ports.

Use

undo loopback-detection control enable

to restore the default.

By default, loopback detection control is disabled on trunk and hybrid ports.
When a hybrid or trunk port detects a loop condition, it sends traps, whether loopback detection control

is enabled or not. However, only after loopback detection control is enabled will the port perform the
protective action configured with the

loopback-detection action

command.

This command does not apply to access ports.

Examples

# Enable loopback detection control on the trunk port GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] loopback-detection enable

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] port link-type trunk

[Sysname-GigabitEthernet1/0/1] loopback-detection enable

[Sysname-GigabitEthernet1/0/1] loopback-detection control enable

Summary of Contents for WA Series






































































































































Search results

Summary of Contents for WA Series

Reviews:

Related manuals for WA Series

Brands by name

Popular brands

H3C WA Series, Layer 2 Command Reference

Search results

Summary of Contents for WA Series

Reviews:

Related manuals for WA Series

Brands by name

Popular brands