manualshive.com logo in svg

H3C WA Series, Layer 2 Command Reference, Page: 30 / 133

Share
Download
H3C WA Series Layer 2 Command Reference Download Page 30

 

22 

Loopback and null interface configuration 
commands 

default 

Syntax 

default 

View 

Loopback interface view, null interface view 

Default level 

2: System level 

Parameters 

None 

Description 

Use 

default

 to restore the default settings of the loopback or null interface.  

Examples 

# Restore the default settings of interface loopback 0.  

<Sysname> system-view 

[Sysname] interface loopback 0 

[Sysname-loopback0] default 

This command will restore the default settings. Continue? [Y/N]:y 

description 

Syntax 

description

 

text

 

undo

 

description

 

View 

Loopback interface view, null interface view 

Default level 

2: System level 

Parameters 

text

: Interface description, a string of 1 to 80 characters. The string can include case-sensitive letters, 

digits, special characters, spaces, and other Unicode characters and symbols.  

 

Summary of Contents for WA Series






































































































































Reviews:

No comments