manualshive.com logo in svg

H3C WA Series, Layer 2 Command Reference, Page: 21 / 133

Share
Download
H3C WA Series Layer 2 Command Reference Download Page 21

13 

reset counters interface 

Syntax 

reset counters interface

 [ 

interface-type

 [ 

interface-number

 ] ] 

View 

User view 

Default level 

2: System level 

Parameters 

interface-type

: Specifies an interface type.

 

interface-type

 

interface-number

: Specifies an interface by its type and number. 

Description 

Use 

reset counters interface 

to clear the Ethernet interface statistics. 

Before collecting traffic statistics for a specific period of time on an interface, clear the old statistics first. 

•

 

If no interface type is specified, this command clears statistics for all interfaces. 

•

 

If only the interface type is specified, this command clears statistics for all interfaces of that type. 

•

 

If both the interface type and the interface number are specified, this command clears statistics for 
the specified interface. 

Examples 

# Clear the statistics of GigabitEthernet 1/0/1. 

<Sysname> reset counters interface gigabitethernet 1/0/1 

shutdown 

Syntax 

shutdown 
undo shutdown 

View 

Ethernet interface view 

Default level 

2: System level 

Parameters 

None 

Description 

Use 

shutdown 

to shut down an Ethernet interface. 

Use 

undo

 

shutdown 

to bring up an Ethernet interface. 

By default, Ethernet interfaces are in the up state. 

Summary of Contents for WA Series






































































































































Reviews:

No comments