manualshive.com logo in svg

H3C WA Series, Layer 2 Command Reference, Page: 68 / 133

Share
Download
H3C WA Series Layer 2 Command Reference Download Page 68

 

60

 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] stp compliance dot1s 

stp config-digest-snooping 

Syntax 

stp config-digest-snooping 
undo stp config-digest-snooping 

View 

System view, Ethernet interface view, WLAN mesh interface view 

Default level 

2: System level 

Parameters 

None 

Description 

Use 

stp config-digest-snooping

 to enable Digest Snooping. 

Use 

undo stp config-digest-snooping

 to disable Digest Snooping. 

The feature is disabled by default. 
Configured in system view, the setting takes effect globally.  
Configured in Ethernet interface view or WLAN mesh interface view, the setting takes effect on the 

interface only.  
Enable this feature both globally and on ports connected to other vendors' devices to make it effective. 

To minimize impact, enable the feature on all associated ports before you enable it globally. 
Related commands: 

display stp

. 

Examples 

# Enable Digest Snooping on GigabitEthernet 1/0/1 and then globally. 

<Sysname> system-view 

[Sysname] interface GigabitEthernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] stp config-digest-snooping 

[Sysname-GigabitEthernet1/0/1] quit 

[Sysname] stp config-digest-snooping 

stp cost 

Syntax 

stp 

[

 instance 

instance-id 

]

 cost 

cost

 

undo stp 

[

 instance 

instance-id 

]

 cost 

View 

Ethernet interface view, WLAN mesh interface view 

Summary of Contents for WA Series






































































































































Reviews:

No comments