manualshive.com logo in svg

H3C WA Series, Layer 2 Command Reference, Page: 12 / 133

Share
Download
H3C WA Series Layer 2 Command Reference Download Page 12

4 

          975 unicasts, 141 broadcasts, 0 multicasts, - pauses 

 Output: 0 output errors, 0 underruns, 0 buffer failures 

          0 aborts, 0 deferred, 0 collisions, 0 late collisions 

          - lost carrier, 0 no carrier                                                       

Table 1

 

display interface command (in bridge mode) output description 

Field Description 

GigabitEthernet1/0/1 current 
state 

Physical state of the Ethernet interface. For more information, see 

Table 2

. 

IP Packet Frame Type 

Ethernet framing format on the interface. 

100Mbps-speed mode, 
full-duplex mode 

The interface operates at 100 Mbps and in full-duplex mode. 

Link speed type is 
autonegotiation 

The interface will negotiate a speed with its peer. 

link duplex type is 
autonegotiation 

The interface will negotiate a duplex mode with its peer. 

The Maximum Frame Length 

The maximum Ethernet frame length allowed on the interface, which varies 
by device model. For more information, see 

About the WA Series Access 

Points Configuration Guides

. 

Broadcast MAX-ratio 

Broadcast suppression threshold as a percentage of the interface 
transmission capability. When the threshold is exceeded, the interface 
drops broadcast packets. 

Unicast MAX-ratio 

Unknown unicast suppression threshold as a percentage of the interface 
transmission capability. When the threshold is exceeded, the interface 

drops unknown unicast packets. 

Multicast MAX-ratio 

Multicast suppression threshold as a percentage of the interface 
transmission capability. When the threshold is exceeded, the interface 

drops multicast packets. 

PVID 

Port VLAN ID. 

Port link-type 

Link type of the interface, which can be access, trunk, and hybrid. 

Tagged   VLAN ID 

VLANs for which the interface sends packets without removing VLAN tags. 

Untagged VLAN ID 

VLANs for which the interface sends packets after removing VLAN tags. 

Last clearing of counters 

Time when the 

reset counts interface

 command was last used to clear 

statistics on the interface. 

Never

 will be displayed if the 

reset counts 

interface

 command was never used since the device was started. 

Last 300 seconds input:  0 
packets/sec 70 bytes/sec 0% 
 Last 300 seconds output:  0 

packets/sec 64 bytes/sec 0%

 

Average rate of input and output traffic in the last 300 seconds, in pps and 
Bps. 
-% indicates the ratio of the actual port speed to the rated port speed 

expressed in percentage. 

Input (total):  1945 packets, 
247903 bytes 
          1156 unicasts, 688 

broadcasts, 101 multicasts, - 
pauses 

Inbound traffic statistics (in packets and bytes) for the interface. All inbound 
normal and abnormal packets (including unicast, broadcast, and multicast), 

and pause frames were counted. 
A hyphen (-) is displayed for an unsupported statistical item. 

Summary of Contents for WA Series






































































































































Reviews:

No comments