background image

 

36 

mac-address mac-learning disable 

Syntax 

mac-address mac-learning disable 
undo mac-address mac-learning disable 

View 

System view, Ethernet interface view, WLAN-BSS interface view 

Default level 

2: System level 

Parameters 

None 

Description 

Use 

mac-address mac-learning disable 

to disable MAC address learning globally or on an interface. 

Use 

undo mac-address mac-learning disable

 to enable MAC address learning globally or on an 

interface.  
By default, MAC address learning is enabled. 
Follow these guidelines when you configure MAC address learning:  

 

You may need to disable MAC address learning to prevent the MAC address table from being 
saturated. For example, when your device is being attacked by a great deal of packets with 

different source MAC addresses, the update of the MAC address table can be affected. 

 

Because disabling MAC address learning may result in broadcast storms, enable broadcast storm 
suppression after you disable MAC address learning on a port. 

Related commands: 

display mac-address mac-learning

Examples 

# Disable global MAC address learning. 

<Sysname> system-view 

[Sysname] mac-address mac-learning disable 

# Disable MAC address learning on port GigabitEthernet 1/0/1. 

<Sysname> system-view 

[Sysname] interface gigabitethernet 1/0/1 

[Sysname-GigabitEthernet1/0/1] mac-address mac-learning disable 

mac-address max-mac-count 

Syntax 

mac-address max-mac-count

 { 

count

 | 

disable-forwarding

 }

 

undo mac-address max-mac-count 

disable-forwarding

 ]

 

View 

Ethernet interface view, WLAN-BSS interface view 

Summary of Contents for WA Series






































































































































Reviews: