manualshive.com logo in svg

H3C S5830V2 series, Command Reference Manual, Page: 270 / 301

Share
Download
H3C S5830V2 series Command Reference Manual Download Page 270

 

258 

monitor cpu-usage enable 

Use 

monitor cpu-usage enable

 to enable CPU usage recording. 

Use 

undo monitor cpu-usage enable 

to disable CPU usage recording. 

Syntax 

monitor cpu-usage enable 

[ 

slot

 

slot-number 

[ 

cpu

 

cpu-number 

] ]

 

undo monitor cpu-usage enable 

[ 

slot

 

slot-number 

[ 

cpu

 

cpu-number 

] ]

 

Default 

CPU usage recording is enabled. 

Views 

System view 

Predefined user roles 

network-admin 

Parameters 

slot

 

slot-number

: Specifies an IRF member device by its member ID or a PEX by its virtual slot 

number. If you do not specify this option, the command enables CPU usage recording for the master 
device. 

cpu

 

cpu-number

: Specifies a CPU by its number. The 

cpu-number

 argument must be 0. 

Examples 

# Enable CPU usage recording. 

<Sysname> system-view 

[Sysname] monitor cpu-usage enable 

Related commands 

•

 

display cpu-usage configuration 

•

 

display cpu-usage history 

•

 

monitor cpu-usage enable 

•

 monitor 

cpu-usage 

threshold 

monitor cpu-usage interval 

Use 

monitor cpu-usage interval

 to set the CPU usage sampling interval. 

Syntax 

monitor cpu-usage interval interval-value 

[ 

slot

 

slot-number 

[ 

cpu

 

cpu-number 

] ] 

Default 

The CPU usage sampling interval is 1 minute. 

Views 

System view 

Predefined user roles 

network-admin 

Summary of Contents for S5830V2 series














































































































































































































































































































Reviews:

No comments