GW Instek PCS-1000 User Manual Download Page 64

Page: 64 / 93

PCS-1000 User Manual

Query Example

CONF:VOLT?
>”DC 0.1”
The mode is DCV and the range is 200mV.

Note

The range that is returned is the base voltage unit. See
the table below:

Unit

Voltage Range

1000

1000VDC

600

600ACV

100

200V

20V

0.1

200mV

CONFigure:VOLTage[:DC]

Set

Description

This command will set the voltage mode to DC
and set the DCV range. If the range is not specified
then it will not be changed.

Syntax

CONFigure:VOLTage[:DC] [<Range> | AUTO]

Parameter

<Range>

Voltage range <NRf>: 0.0000001 ~ 1050
The unit will automatically be set to the
closest range.

AUTO

Autoset

Example

CONF:VOLT:DC 20
Sets the voltage mode to DC and the DCV range to
20V.

Example

CONF:VOLT:DC
Sets the voltage mode to DC. The range stays the
same.

Summary of Contents for PCS-1000






























































































Search results

Summary of Contents for PCS-1000

Reviews:

Related manuals for PCS-1000

Brands by name

Popular brands

GW Instek PCS-1000, User Manual

Search results

Summary of Contents for PCS-1000

Reviews:

Related manuals for PCS-1000

Brands by name

Popular brands