Gunter & Hauer GH 43 CI Instruction Manual Download Page 17

Günter & Hauer 

16 

Stainless steel parts 

Stains may appear on stainless steel parts if they come into contact with hard water or 
abrasive detergents for a long time. It is recommended to wash them with a soap solution 
and wipe dry with a soft cloth. 
The shine will be preserved if used regularly with appropriate care products. Use special 
detergents for steel. 

Grills, burners 

In  case  of  contamination  of  burners  and  grate,  these  elements  must  be  removed  and 
washed in warm water with the addition of agents that remove grease and dirt. Then 
they  should  be  wiped  dry.  It  is  recommended  to  install  cast  iron  grilles  only  in  the 
appropriate slots, so as not to scratch or damage the panel. The lids of the dividers can 
be washed with a sponge soaked in soapy water or in a solution of mild detergent. After 
washing, they should be wiped dry and carefully put in place. Check that the holes in 
the dividers are blocked. 

Spark plug 

Electric  ignition  is  performed  using  ceramic  and  metal  electrodes.  Keep  these  parts 
clean to prevent ignition difficulties, and make sure that the holes in the burner flame 
cutter are not clogged. Constantly check the cleanliness of the safety valve probe (gas 
control) and the spark plug. This will ensure their optimal functioning. 

Gas valves 

Lubrication of valves, if necessary, should be performed only by a qualified specialist. 

It is not recommended 

to use the following: 

• household detergents with a bleaching effect,
• impregnated sponges, unsuitable for cleaning dishes with non-stick coating;
• metal sponges; stain removers for bathtubs / sinks.

STAIN REMOVAL 

Light spots of pearl color (aluminum residues) can be removed from the cooled down 
hob with a special detergent. 
Lime  stains  (for  example,  boiled  water)  can  be  removed  with  vinegar  or  a  special 
detergent. 
When removing fried sugar, stains containing sugar, burnt plastic and foil, it is better to 
clean  while  the  stove  remains  hot.  You  must  immediately  carefully  scrape  off  the 
remnants (hot) with a sharp object from a hot work surface. After removing the dirt from 
the  hot  surface,  after  the  surface  cools  down,  the  hob  can  be  cleaned  with  a  special 
detergent. 

Summary of Contents for GH 43 CI




















Reviews: