GrowSpan Gothic Premium H5CRU Assembly Instructions Manual Download Page 38

Page: 38 / 55

H5_30_Wide_HT_Roll_Up

Revision date: 06.28.19

Wind Panel Information & Installation

INSTALL THE WIND PANEL ACCESSORY (OPTIONAL)

Wind panels protect the drop-down curtain at each

corner of the shelter. When installed, these panels allow

wind to flow over the corners and around the shelter and

help keep the drop-down curtain in position.

BUILDINGS WITH ROLL-UP SIDES:

Wind panels are

not typically used for roll-up sides as they would hamper

the operation of the panels. However, the D10025824M

material can be used to winterize the corners when the

growing season is over or temperatures drop.

The following wind panel items are included with the

shelter:
• Wind Panel Material: (6' x 8' panel)—D10025824M
• Tek screws (FA4482B), wood screws (FA4652B),

and neo-bonded washers (102921B)

The procedure that follows describes one way to install

the wind panels using Tek screws, wood screws, and

neo-bonded washers. Shelter design and other factors

may require minor adjustments to these instructions.

Fasteners are installed into the end rafter, ribbon boards,

and baseboards.

Additional customer-supplied materials

may be needed for some custom shelters.

Complete the

following steps to install the wind panels:
1. Place the 6' x 8' wind panel material on a flat surface

and cut it into four (4) equal 2' x 6' sections.

3. Place a 2' x 6' wind panel over the end of the drop-

down curtain at one corner of the shelter and align it

with the end rafter as shown below.

4. Using wood screws and washers, secure the top of

the wind panel to the ribbon board. Space the screws

every 12" along the top of the panel.

5. With the panel secured at the top, fold the panel edge

around and attach the panel to the end rafter using

Tek screws and washer. Space the Tek screws every

6-8 inches.

6. Secure the bottom of the panel to the baseboard

using wood screws and washers.

Step 4

Step 5

Step 6

NOTE:

If needed, trim access material along the

edge of the end wall. Drawings are not to scale.

7. Read the care and maintenance info on the next

page.

FA4652 Wood Screw

FA4482B

Tek Screw

102921B

Washers

2. Using the crank assembly, roll the curtain up until it is

a few inches below the ribbon board.

Summary of Contents for Gothic Premium H5CRU
























































Search results

Summary of Contents for Gothic Premium H5CRU

Reviews:

Related manuals for Gothic Premium H5CRU

Brands by name

Popular brands

GrowSpan Gothic Premium H5CRU, Assembly Instructions Manual

Search results

Summary of Contents for Gothic Premium H5CRU

Reviews:

Related manuals for Gothic Premium H5CRU

Brands by name

Popular brands