
FASTENING THE BODY OF THE SKIMMER TO THE POOL: (Follow the instructions for the skimmer corresponding to your
filter system).
Join the mouth (B) of the skimmer to its body (S) fitting a single seal (J) between the two.
Continue filling the pool with water until there is a 4 cm gap between the water and the lower edge of the skimmer perforation
mark. Use a Stanley knife to cut the liner (L) where the perforation mark is located inside the pool. Fit the double seal (JJ) so
that the channels (channels of the double seal) hold the wall plate and the liner. Next, fit the screws from the inside of the pool
to the body of the skimmer (S). Cover the connection sleeve (C) and the filter system water intake with Teflon. Screw the connection
sleeve (C) tight to the body of the skimmer and connect one end of the hose to the skimmer connection sleeve (C).
IMPORTANT: Apply Teflon to all the water connection threads.
FITTING THE SKIMMER FRAME (MS):
Make sure that all the holes are aligned (seal-perforation, wall plate-skimmer). Insert the remaining screws through the frame
without screwing them too tight to check that the fit is correct. Fasten the screws a little, one after the other in the indicated order.
FINALLY, FASTEN THEM TIGHT IN THE SAME ORDER. FINAL DETAILS: snap-fit the trim cover of the skimmer frame (Z) in
place. To finish, insert the flap (K) through the rectangular opening (press both ends with care and fit the tabs in place). Place
the basket (O) in position inside the skimmer and the skimmer body cover (TS). FILL THE POOL UP TO HALF THE HEIGHT
OF THE SKIMMER FLAP (10-15 cm below the edge of the pool) SO THAT WATER ENTERS THE SKIMMER AND FILLS THE
FILTER SYSTEM. Before doing this, make sure you have connected the SKIMMER to the corresponding inlet of the TECHNICAL
FILTRATION HOUSING with the corresponding hose.
39
PEOV9159 - PEOV8059 - PEOV7059 - PEOV6059 - PEOV5059 - PE5559 - PE4259 - PE3559
PEOV9127 - PEOV8027 - PEOV7027 - PEOV6027 - PEOV5027 - PE5527 - PE4227 - PE3527
DK
FASTGØRELSE AF AFLØBET TIL POOLEN: (Følg vejledningen for det afløb, der svarer til dit filtersystem).
Fastgør afløbsåbningen (B) til hoveddelen (S) med en enkelt pakning (J) mellem dem.
Fortsæt med at fylde poolen med vand, indtil der er 4 cm fra vandet til den nederste kant af perforeringsmærket til afløbet. Brug
en hobbykniv til at skære hul i dugen (L) ved perforeringsmærket indvendigt i poolen. Monter den dobbelte pakning (JJ), så dens
kanaler holder vægpladen og dugen. Før derefter skruerne igennem fra indersiden af poolen til afløbets hoveddel (S). Dæk
forbindelsesmuffen (C) og filtersystemets vandindtag med Teflon. Skru forbindelsesmuffen (C) stramt fast til afløbets hoveddel,
og forbind den ene ende af slangen til afløbets forbindelsesmuffe (C).
VIGTIGT: Brug Teflon på alle vandtilslutningers gevind.
MONTERING AF AFLØBETS RAMME (MS):
Sørg for, at alle huller flugter (pakning, perforering, vægplade, afløb). Før de resterende skruer gennem rammen uden at stramme
dem for meget for at kontrollere, at alting passer sammen. Spænd skruerne lidt, den ene efter den anden, i den angivne
rækkefølge.TIL SIDST STRAMMES DE HELT I SAMME RÆKKEFØLGE.
AFSLUTTENDE DETALJER: Pres coveret til afløbets ramme (Z) på plads. Til sidst indsættes klappen (K) gennem den rektangulære
åbning (tryk forsigtigt i begge ender, og før tapperne på plads). Anbring kurven (O) inde i afløbet og coveret til afløbets hoveddel
(TS). FYLD POOLEN, TIL VANDET NÅR HALVVEJS OP OVER AFLØBSKLAPPEN (10-15 cm under poolkanten), SÅ VAND
LØBER IND I AFLØBET OG FYLDER FILTERSYSTEMET. Før du gør dette, skal du sørge for, at du har tilsluttet AFLØBET til
det tilsvarende indtag på det TEKNISKE FILTRERINGSHUS med den korrekte slange.
3
TA
O
C
S
J
B
K
JJ
MS
Z
TS
POOL EXTERIOR
POOLENS YDERSIDE
UIMA-ALTAAN ULKOPUOLI
BASSENGETS UTSIDE
POOL UTSIDA
POOL INTERIOR
POOLENS INDERSIDE
ALTAAN SISÄPUOLI
BASSENGETS INNSIDE
POOL INSIDA
WATER
VAND
VESI
VANN
VATTEN
SINGLE SEAL
ENKELT PAKNING
YKSINKERTAINEN TIIVISTE
ENKEL PAKNING
ENKEL TÄTNING
DOUBLE SEAL
DOBBELT PAKNING
KAKSINKERTAINEN TIIVISTE
DOBBEL PAKNING
DUBBEL TÄTNING
SCREWS
SKRUER
RUUVIT
SKRUER
SKRUVAR
SCREWS
SKRUER
RUUVIT
SKRUER
SKRUVAR
SCREWS
SKRUER
RUUVIT
SKRUER
SKRUVAR
WATER LEVEL
VANDSTAND
VEDENKORKEUS
VANNIVÅ
VATTENNIVÅ
POOL INTERIOR
POOLENS INDERSIDE - ALTAAN SISÄPUOLI
BASSENGETS INNSIDE - POOL INSIDA
POOL EXTERIOR
POOLENS YDERSIDE - UIMA-ALTAAN ULKOPUOLI
BASSENGETS UTSIDE - POOL UTSIDA