GENERAL:
Do not mount or demount tires without
proper training. Follow all procedures and
safety instructions. Wall charts containing
mounting and demounting instructions for
all Goodyear on-highway rims are avail-
able through your Goodyear rim supplier.
Ask for “ON-HIGHWAY RIM MOUNT-
ING AND DEMOUNTING CHART SET
NO. TR71-2042". This set contains five
charts covering all Goodyear on-highway
rims.
“MULTIPIECE RIM/WHEEL MATCH-
ING CHARTS” are available through
Motor Wheel Corporation and the United
States Department of Transportation
(DOT), Washington, D.C.
DEMOUNTING:
Always exhaust all air from a single tire
and from both tires of a dual assembly
prior to removing any rim components or
any wheel components such as nuts and
rim clamps.
Make sure to remove valve core to ex-
haust all air from the tire. Remove both
cores from a dual assembly.
Check the valve stem by running a piece of
wire through the stem to make sure it is
not plugged.
For safety’s sake, always remove the valve core and exhaust all air from a
single tire and from both tires of a dual assembly prior to removing any
rim components, or any wheel components, such as nuts and rim
clamps.
Check the valve stem by running a piece of wire through the stem to
make sure it Is not plugged
IMPORTANT
!
!
!
!
!
TIRE and RIM SERVICING SAFETY
INSPECTION:
Clean rims and repaint to stop detrimen-
tal effects of corrosion and facilitate
checking and tire mounting. Be very care-
ful to clean all dirt and rust from the lock
ring and gutter. This is important to
secure the lock ring in its proper position.
A filter on the air inflation equipment to
remove the moisture from the air line
helps prevent corrosion. The filter should
be checked periodically to see that it is
w o r k i n g p r o p e r l y.
Check rim components periodically for
cracks. Replace all cracked, badly worn,
damaged and severely rusted components
with new parts of same size and type.
W h e n i n d o u b t r e p l a c e .
Do not, under any circumstances, attempt
to rework, weld, heat, or braze any rim
components that are cracked, broken, or
damaged. Replace with new parts or parts
that are not cracked, broken, or damaged
and which are of the same size and type.
Make sure correct parts are being assem-
bled. Check DOT chart, your distributor
or the manufacturer if you have any
d o u b t s .
Don’t be careless or take chances. If you
are not sure about the proper mating of
rim and wheel parts, consult a rim and
wheel expert. This may be the tire man
who is servicing your fleet, the rim and
wheel distributor in your area, or the
M o t o r W h e e l s a l e s e n g i n e e r .
!
!
!
!
!
13
Summary of Contents for LOED 534A
