background image

Remove isolation plate (11), sealing
strip (17), end separators (15)
center separator (16), back-up ring
(14), and o-ring (35). (No isola-
tion plates nor separators in SPM25.)

Remove the body (2) by lightly
tapping the sides with a wooden
mallet or plastic hammer, while
lifting it with the other hand.
Remove o-ring (34). (Fig. 83)

Remove the spline coupling (31).
(Fig. 84)

10.

11.

12.

13.

14.

59

FIGURE 81

FIGURE 83

FIGURE 82

FIGURE 84

Lift drive gear (5) and idler gear
( 7 )   s t r a i g h t   u p   o u t   o f   t h e   m o t o r
b o d y.   ( F i g .   81)

 

To remove the bottom pressure plate

(9) (13, in SPM25) from the motor
body, use an adjustable sleeve bear-
ing puller. (A puller of this type
is listed in McMasters and Carr ’s
catalog under part number 6354N14).
Insert the puller in the pressure
plate bore. With a very light
rocking motion applied to the puller
handle, unseat the plate. Lift it
straight up and out of the motor
body. Use extreme care in the
removal of this plate. Do not
attempt to pry or force it. (Fig.82)

Summary of Contents for LOED 534A




























































































Reviews: