PLANETARY HUBS
ASSEMBLY PROCEDURE FOR MAJOR ASSEMBLY
S t a r t w i t h h u b - s p i n d l e s u b - a s s e m b l y ( 1 ) w i t h l a r g e o p e n e n d u p .
A s s e m b l e i n t e r n a l g e a r ( 2 ) o n t o t h e s p i n d l e o f h u b - s p i n d l e s u b - a s s e m b l y ( 1 ) .
P l a c e t h r u s t w a s h e r ( 1 5 ) o n t o t h e s p i n d l e p i l o t o f h u b - s p i n d l e s u b - a s s e m b l y ( 1 ) .
P l a c e t h r u s t b e a r i n g ( 1 6 ) o n t o s p i n d l e p i l o t o f h u b - s p i n d l e s u b - a s s e m b l y ( 1 ) .
P l a c e t h r u s t w a s h e r ( 1 5 ) o n t o s p i n d l e p i l o t o f h u b - s p i n d l e s u b - a s s e m b l y ( 1 ) .
D r o p s p a c e r w a s h e r ( 7 ) i n t o s p i n d l e o f h u b - s p i n d l e s u b - a s s e m b l y ( 1 ) .
P l a c e s p r i n g ( 8 ) i n t o s p i n d l e o f h u b - s p i n d l e s u b - a s s e m b l y ( 1 ) .
P l a c e s p a c e r w a s h e r ( 7 ) i n t o s p i n d l e o f h u b - s p i n d l e s u b - a s s e m b l y ( 1 ) .
S e c u r e r e t a i n i n g r i n g ( 9 ) i n t o g r o o v e i n s p i n d l e o f h u b - s p i n d l e s u b - a s s e m b l y ( 1 ) .
S e c u r e r e t a i n i n g r i n g ( 1 0 ) i n g r o o v e o n i n p u t s h a f t ( 1 1 ) .
P l a c e l o n g s p l i n e d e n d o f i n p u t s h a f t ( 1 1 ) i n t o s p i n d l e o f h u b - s p i n d l e h u b -
assembly (1).
S l i d e t h r u s t s p a c e r ( 1 2 ) o n t o i n p u t s h a f t ( 1 1 ) .
P u t “ O ” r i n g ( 5 ) i n h u b c o u n t e r b o r e o f h u b - s p i n d l e .
P l a c e c a r r i e r s u b - a s s e m b l y ( 3 ) o n a f l a t s u r f a c e w i t h l a r g e g e a r s u p . F i n d
m a r k e d ( p u n c h m a r k e d ) t e e t h o n t h e l a r g e g e a r s . R o t a t e u n t i l t h e m a r k s a r e i n
a s t r a i g h t - u p p o s i t i o n . ( S e e F i g u r e ) .
Place ring gear (4) over large gears of carrier sub-assembly (3).
Holding ring gear (4) in mesh with large gears, pick-up carrier sub-assembly (3)
u n t i l m a r k e d h o l d i s l o c a t e d o v e r o n e o f t h e c o u n t e r b o r e d h o l e s i n h u b o f h u b -
spindle sub-assembly (1). Carrier sub-assembly (3) must rotate freely.
P u t i n p u t g e a r ( 1 3 ) o v e r i n p u t s h a f t ( 1 1 ) a n d m e s h i n g w i t h l a r g e g e a r s o f c a r r i e r
s u b - a s s e m b l y. B e s u r e t h a t i n p u t g e a r ( 1 3 ) r e l i e f i s a s s h o w n . ( S e e F i g u r e ) .
P u t “ O ” r i n g ( 5 ) i n t o c o v e r c o u n t e r b o r e o f c o v e r s u b - a s s e m b l y ( 6 ) . H o l d “ O ”
ring in place with petroleum jelly or grease.
Place thrust washer (15) into carrier counterbore of carrier sub-assembly (3).
Place thrust bearing (16) into carrier counterbore of carrier sub-assembly (3).
Place thrust washer (15) into carrier counterbore of carrier sub-assembly (3).
P l a c e c o v e r s u b - a s s e m b l y ( 6 ) o n t o r i n g g e a r ( 4 ) w i t h o i l c h e c k p l u g i n c o v e r
sub-assembly (6) located 90 from oil fill plug in hub-assembly sub-assembly
(1).
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
24
Summary of Contents for LOED 534A
