Goulds Pumps 3700i API610 Installation, Operation And Maintenance Manual Download Page 18

Page: 18 / 126

Figure 3: Example of a proper lifting method of pump and driver on base plate

Figure 4: Example of a proper lifting method of pump on base plate with driver and motor

2.3 Storage guidelines

2.3.1 Pump storage requirements

Storage requirements depend on the amount of time that you store the unit. The normal packaging is
designed only to protect the unit during shipping.

Length of time in storage

Storage requirements

Upon receipt/short-term (less than six
months)

•

Store in a covered and dry location.

•

Store the unit free from dirt and vibrations.

Long-term (more than six months)

•

Store in a covered and dry location.

•

Store the unit free from heat, dirt, and vibrations.

2.3 Storage guidelines

Model 3700i API610 / Type OH2 Installation, Operation, and Maintenance Manual

Summary of Contents for 3700i API610































































































































Search results

Summary of Contents for 3700i API610

Reviews:

Related manuals for 3700i API610

Brands by name

Popular brands

Goulds Pumps 3700i API610, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for 3700i API610

Reviews:

Related manuals for 3700i API610

Brands by name

Popular brands